The closer you look, the less you see!
Printplaat en ontwerp
After you flashed the firmware with the “UnifiedEngineering” version, you can place a cold junction temperature sensor for better temperatur management. From github: The existing controller makes the assumption that the cold-junction is at 20 degrees Celsius at all times …
T-962 reflow oven 31 – Cold junction compensation Lees meer »
Op deze pagina vind je een aantal handige eigenschappen van SMD componenten en herkenning van codes e.d. Weerstanden Waarden SMT E96 letter codes Eigenschappen (wattage) Zekeringen Waarde opdruk
Hardware board Pictures from ka4designs Processor pinout
|
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 |
CPU: LPC2134 Vref: 3.3V Display: WYM12864D2 (128x64) D0..7: P1.16 .. P1.23 EN: P0.18 R/W: P0.19 RS: P0.22 CS1: P0.13 CS2: P0.12 K: P0.11 (backlight via BCP68) Buttons: pullups, schalten gegen GND -> low active F1: P0.23 F2: P0.15 F3: P0.16 F4: P0.4 S: P0.20 74HC04D: 1A: P0.9 -> 6A -> 6Y -> Lamp LED, Lamp 2A: P0.8 -> 5A -> 5Y -> Fan LED, Fan EEPROM: SDA: P0.3 SCL: P0.2 Beeper: P0.21: via R11 (331) links oben + V1 27L2C: 1OUT: AD0.1 (1IN+: CH A) 2OUT: AD0.2 (2IN+: CH B) red LED: P0.31 |
Schematics
Firmware replacement The standard T-962 firmware is very simple and there are a few flaws in it (temperature overshoot, no coldjuntion compensation, no pwm controlled fan, etc). There is a opensource firmware build on github: https://github.com/UnifiedEngineering/T-962-improvements Github page T-962 reflow …
Tape replacement As far as we know every unit comes with tape on the heating shield (to prevent shotages from wiring and stuff), this is default masking tape and smells very bad when the oven is in use (some say …
Earth connection Safety first!, before powering on the device, open it up and check the wiring of the earth connection on the outside casing, because of the case powder coating it will make NO contact, unscrew it and grind the …
1) The T962 is a self-contained Micro-Processor controlled IC Heater and solder rework station . 2) Uses up to 800 watts of energy efficient infrared heating and air circulation to reflow solder in a large 180mm*235mm area. 3) Parameters of …
Bron: Wikipedia Informatie (ENG) Through-hole technology (also spelled “thru-hole”), refers to the mounting scheme used for electronic components that involves the use of leads on the components that are inserted into holes drilled in printed circuit boards (PCB) and soldered …
Bron: Wikipedia Surface-mounted device, afkorting SMD, is een term uit de elektrotechniek en betekent letterlijk ‘oppervlak-gemonteerde component’. In tegenstelling tot een component met aansluitdraden (Engels: through-hole, doorvoergat) wordt een SMD-onderdeel niet gemonteerd met behulp van draadverbindingen door de printplaat heen, …
Bron: electronics-tutorials.ws Generally, the actual values of Capacitance, Voltage or Tolerance are marked onto the body of the capacitors in the form of alphanumeric characters. However, when the value of the capacitance is of a decimal value problems arise with …