Plugwise - Stretch 2.0 Archieven - DomoticX Knowledge Center

Plugwise Stretch – Hardware van Circle modules

Door Sebastiaan Geplaatst op 2017-03-20 Geplaatst in Plugwise - Stretch 2.0 Getagd met Circle, Hardware, Module, Plugwise, Stretch 2.0

Hieronder enkele foto’s van de binnenkant van een Plugwise Circle

Plugwise Stretch 2.0 – Firmware bestanden

Door Sebastiaan Geplaatst op 2016-06-11 Geplaatst in Plugwise - Stretch 2.0 Getagd met Firmware, Plugwise, Stretch 2.0

Firmware bestanden van de Stretch 2.0, gedownload vanaf de PlugWise server.

Firmware 2.3.9
NL:
Met deze update zal de Stretch voortaan gebruik maken de verbeterde PlugwiseCloud-diensten. Let op: Na de update werkt alleen de nieuwste Plugwise Mobile app met de Stretch en het kan een dag duren voordat u uw historische gegevens weer kunt inzien.

ENG:
With this update the Stretch will start using the improved Plugwise Cloud services. Note: After this update only the newest version of the Plugwise Mobile app will work with this Stretch and it can take up to a day before you can view your historic data again.


Firmware van 2.2.3 > 2.2.15
NL:
Stretch schakelt sneller en werkt beter met grote netwerken.
Tijdzone instellen en modules uit netwerk verwijderen werkt beter.

ENG:
Stretch switches faster and works better with big networks.
Setting timezone and removing modules from network has been improved.


Firmware van 2.1.8 > 2.2.3
NL:
Stretch schakelt sneller en werkt beter met grote netwerken.
Tijdzone instellen en modules uit netwerk verwijderen werkt beter

ENG:
Stretch switches faster and works better with big networks.
Setting timezone and removing modules from network has been improved.


v2.1.8
NL:
- Stretch reageert sneller en zal grafieken beter updaten.
- Oplossing voor gestopte grafieken
- Supportverbinding (3x kort op de resetknop drukken geeft 24 uur toegang) is verbeterd.

ENG:
Stretch reacts faster and will update its charts better.
Solution for charts that do not update anymore.
The support connection (which is opened or prolonged for 24h each time the reset button is thrice pressed) has been improved.


v2.0.16
NL:
- Grafiekdata wordt beter opgehaald.
- Sneller opstarten bij grote netwerken.
- Zondag-bug in schakelschema opgelost.
- Stretch reageert sneller bij gebruik van meerdere apps.
- Modules worden niet meer onterecht off-line getoond.
- Schakelt geen apparaten uit na een reset.

ENG:
- Chart data fetching from modules improved.
- Faster startup for big networks. Sunday bug in schedules fixed.
- Stretch is more responsive in case of usage with multiple apps.
- Modules are not being faulty displayed as off-line.
- Does not switch appliances off after reset.


v1.0.46
NL:
- Deze versie bevat een oplossing voor Stretches waarvan Sommige apparaten ineens geen grafieken meer hadden.
- Let op: het kan meerdere dagen duren voordat de grafieken weer beschikbaar zijn.
- Tevens lost deze update de gevallen op waarin de Stretch in huis soms ineens niet bereikbaar was via het WiFi netwerk.

ENG:
- This version contains a fix for Stretches from which the charts of some appliances stopped suddenly.
- Warning: it can take several days before the charts are up-to-date again.
- Moreover will this update fix the issue of a lost WiFi connection in your home network.


v1.0.41
Changes since 1.0.38:
- Removed automatic reboot at night-
- Added web interface for Backup and Restore

----------
Sprongen bij updates firmware door plugwise:

1.0.38 --> 1.0.41
1.0.41 --> 1.0.46
1.0.46 --> no upgrade
1.0.46 --> 2.0.16 (handmatig geforceerd)
2.0.16 --> 2.1.8
2.2.15 --> 2.3.9

Firmware 2.3.9

NL:

Met deze update zal de Stretch voortaan gebruik maken de verbeterde PlugwiseCloud-diensten. Let op: Na de update werkt alleen de nieuwste Plugwise Mobile app met de Stretch en het kan een dag duren voordat u uw historische gegevens weer kunt inzien.

ENG:

With this update the Stretch will start using the improved Plugwise Cloud services. Note: After this update only the newest version of the Plugwise Mobile app will work with this Stretch and it can take up to a day before you can view your historic data again.

Firmware van 2.2.3 > 2.2.15

NL:

Stretch schakelt sneller en werkt beter met grote netwerken.

Tijdzone instellen en modules uit netwerk verwijderen werkt beter.

ENG:

Stretch switches faster and works better with big networks.

Setting timezone and removing modules from network has been improved.

Firmware van 2.1.8 > 2.2.3

NL:

Stretch schakelt sneller en werkt beter met grote netwerken.

Tijdzone instellen en modules uit netwerk verwijderen werkt beter

ENG:

Stretch switches faster and works better with big networks.

Setting timezone and removing modules from network has been improved.

v2.1.8

NL:

- Stretch reageert sneller en zal grafieken beter updaten.

- Oplossing voor gestopte grafieken

- Supportverbinding (3x kort op de resetknop drukken geeft 24 uur toegang) is verbeterd.

ENG:

Stretch reacts faster and will update its charts better.

Solution for charts that do not update anymore.

The support connection (which is opened or prolonged for 24h each time the reset button is thrice pressed) has been improved.

v2.0.16

NL:

- Grafiekdata wordt beter opgehaald.

- Sneller opstarten bij grote netwerken.

- Zondag-bug in schakelschema opgelost.

- Stretch reageert sneller bij gebruik van meerdere apps.

- Modules worden niet meer onterecht off-line getoond.

- Schakelt geen apparaten uit na een reset.

ENG:

- Chart data fetching from modules improved.

- Faster startup for big networks. Sunday bug in schedules fixed.

- Stretch is more responsive in case of usage with multiple apps.

- Modules are not being faulty displayed as off-line.

- Does not switch appliances off after reset.

v1.0.46

NL:

- Deze versie bevat een oplossing voor Stretches waarvan Sommige apparaten ineens geen grafieken meer hadden.

- Let op: het kan meerdere dagen duren voordat de grafieken weer beschikbaar zijn.

- Tevens lost deze update de gevallen op waarin de Stretch in huis soms ineens niet bereikbaar was via het WiFi netwerk.

ENG:

- This version contains a fix for Stretches from which the charts of some appliances stopped suddenly.

- Warning: it can take several days before the charts are up-to-date again.

- Moreover will this update fix the issue of a lost WiFi connection in your home network.

v1.0.41

Changes since 1.0.38:

- Removed automatic reboot at night-

- Added web interface for Backup and Restore

----------

Sprongen bij updates firmware door plugwise:

1.0.38 --> 1.0.41

1.0.41 --> 1.0.46

1.0.46 --> no upgrade

1.0.46 --> 2.0.16 (handmatig geforceerd)

2.0.16 --> 2.1.8

2.2.15 --> 2.3.9

[#/plugwise/stretch20/firmware” ]

Plugwise Stretch 2.0 – Communicatie module (perl)

Door Sebastiaan Geplaatst op 2015-07-02 Geplaatst in Plugwise - Stretch 2.0 Getagd met Communicatie, Perl, Plugwise, Stretch 2.0

Website / Bron Download @ CPAN.org Download @ GitHub Informatie (ENG)

NAME
    Device::Plugwise - Perl module to communicate with Plugwise hardware

VERSION
    version 0.5

SYNOPSIS
      my $plugwise = Device::Plugwise->new(device => '/dev/cu.usbserial01');
      $plugwise->command('on', 'ABCDEF'); # Enable Circle#ABCDEF
      while (1) {
        my $message = $plugwise->read();
        print $message, "\n";
      }

      $plugwise = Device::Plugwise->new(device => 'hostname:port');
      $plugwise->command('on', 'ABCDEF'); # Enable Circle#ABCDEF

DESCRIPTION
    Module for interfacing to Plugwise hardware.

    Current implemented functions are

    Switching ON/OFF of circles
    Query circles for their status
    Query the Circles+ for known circles
    Retrieve the live power consumption of a Circle
    Readout the historic power consumption of a Circle (1-hour average)

    IMPORTANT: This module required Plugwise firmware v2.37 or higher.

METHODS
  "new(%parameters)"
    This constructor returns a new Device::Plugwise object. Supported
    parameters are listed below

    device
        The name of the device to connect to, The value can be a tty device
        name of "hostname:port" for a TCP connection. This parameter is
        required.

    filehandle
        The name of an existing filehandle to be used instead of the
        'device' parameter.

    baud
        The baud rate for the tty device. The default is 9600.

    port
        The port for a TCP device. There is no default port.

  "device()"
    Returns the device used to connect to the equipment. If a filehandle was
    provided this method will return undef.

  "baud()"
    Returns the baud rate. Only makes sense when connected over a serial
    connection.

  "port()"
    Returns the TCP port for the device. Only makes sense when using this
    type of connection of course.

  "filehandle()"
    This method returns the file handle for the device.

  "list_circles_count()"
    This method returns the number of Circles that will be interrogated with
    the list_circles command. If you have more than 16 Circles in your
    network, increase the setting to a higher value.

  "read([$timeout])"
    This method blocks until a new message has been received by the device.
    When a message is received the message string is returned. An optional
    timeout (in seconds) may be provided.

  "read_one(\$buffer, [$do_not_write])"
    This method attempts to remove a single message from the buffer passed
    in via the scalar reference. When a message is removed a data structure
    is returned that represents the data received. If insufficient data is
    available then undef is returned.

    By default, a received message triggers sending of the next queued
    message if the $do_no_write parameter is set then writes are not
    triggered.

  "write($command, $callback)"
    This method queues a command for sending to the connected device. The
    first write will be written immediately, subsequent writes are queued
    until a response to the previous message is received.

  "queue_size()"
    This method reports the number of commands that are in the queue to be
    sent to the stick.

  "status()"
    This method returns the status of the internal _plugwise hash. This can
    be used to extract network information and for debugging. Hash entries
    include

    connected : is the software connected to the USB stick
    stick_MAC : Zigbee MAC address of the stick
    network_key : Full zigbee network ID
    short_key : Short version of the network ID
    circles : List of IDs of Circles that have responded to a calibration
    request and that hence are known to be active on the wireless network

  "command($command, $target)"
    This method sends a command to the stick.

    Supported $commands with a target id are:

    on : switch a circle on
    off : switch a circle off
    status : request the current switch state, internal clock, live power
    consumption
    livepower : request the current power measured by the Circle
    history : request the energy consumption for a specific logaddress

    $target can either be a single short hardware MAC address or a
    comma-separated list of devices if multiple devices need to receive the
    same command.

ACKNOWLEDGEMENTS
    The code of this module is heavily based the code by Mark Hindess
    (Device::Onkyo), thanks Mark! The initial Perl Plugwise interface code
    for firmware v1 was written by Jfn.

AUTHOR
    Lieven Hollevoet <hollie@cpan.org>

COPYRIGHT AND LICENSE
    This software is copyright (c) 2012 by Lieven Hollevoet.

    This is free software; you can redistribute it and/or modify it under
    the same terms as the Perl 5 programming language system itself.

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

NAME

Device::Plugwise - Perl module to communicate with Plugwise hardware

VERSION

version 0.5

SYNOPSIS

my $plugwise = Device::Plugwise->new(device => '/dev/cu.usbserial01');

$plugwise->command('on', 'ABCDEF'); # Enable Circle#ABCDEF

while (1) {

my $message = $plugwise->read();

print $message, "\n";

}

$plugwise = Device::Plugwise->new(device => 'hostname:port');

$plugwise->command('on', 'ABCDEF'); # Enable Circle#ABCDEF

DESCRIPTION

Module for interfacing to Plugwise hardware.

Current implemented functions are

Switching ON/OFF of circles

Query circles for their status

Query the Circles+ for known circles

Retrieve the live power consumption of a Circle

Readout the historic power consumption of a Circle (1-hour average)

IMPORTANT: This module required Plugwise firmware v2.37 or higher.

METHODS

"new(%parameters)"

This constructor returns a new Device::Plugwise object. Supported

parameters are listed below

device

The name of the device to connect to, The value can be a tty device

name of "hostname:port" for a TCP connection. This parameter is

required.

filehandle

The name of an existing filehandle to be used instead of the

'device' parameter.

baud

The baud rate for the tty device. The default is 9600.

port

The port for a TCP device. There is no default port.

"device()"

Returns the device used to connect to the equipment. If a filehandle was

provided this method will return undef.

"baud()"

Returns the baud rate. Only makes sense when connected over a serial

connection.

"port()"

Returns the TCP port for the device. Only makes sense when using this

type of connection of course.

"filehandle()"

This method returns the file handle for the device.

"list_circles_count()"

This method returns the number of Circles that will be interrogated with

the list_circles command. If you have more than 16 Circles in your

network, increase the setting to a higher value.

"read([$timeout])"

This method blocks until a new message has been received by the device.

When a message is received the message string is returned. An optional

timeout (in seconds) may be provided.

"read_one(\$buffer, [$do_not_write])"

This method attempts to remove a single message from the buffer passed

in via the scalar reference. When a message is removed a data structure

is returned that represents the data received. If insufficient data is

available then undef is returned.

By default, a received message triggers sending of the next queued

message if the $do_no_write parameter is set then writes are not

triggered.

"write($command, $callback)"

This method queues a command for sending to the connected device. The

first write will be written immediately, subsequent writes are queued

until a response to the previous message is received.

"queue_size()"

This method reports the number of commands that are in the queue to be

sent to the stick.

"status()"

This method returns the status of the internal _plugwise hash. This can

be used to extract network information and for debugging. Hash entries

include

connected : is the software connected to the USB stick

stick_MAC : Zigbee MAC address of the stick

network_key : Full zigbee network ID

short_key : Short version of the network ID

circles : List of IDs of Circles that have responded to a calibration

request and that hence are known to be active on the wireless network

"command($command, $target)"

This method sends a command to the stick.

Supported $commands with a target id are:

on : switch a circle on

off : switch a circle off

status : request the current switch state, internal clock, live power

consumption

livepower : request the current power measured by the Circle

history : request the energy consumption for a specific logaddress

$target can either be a single short hardware MAC address or a

comma-separated list of devices if multiple devices need to receive the

same command.

ACKNOWLEDGEMENTS

The code of this module is heavily based the code by Mark Hindess

(Device::Onkyo), thanks Mark! The initial Perl Plugwise interface code

for firmware v1 was written by Jfn.

AUTHOR

Lieven Hollevoet <hollie@cpan.org>

This is free software; you can redistribute it and/or modify it under

the same terms as the Perl 5 programming language system itself.

[#/plugwise/overig/plugwise_perl_communicatie_module” ]

Plugwise Stretch 2.0 – HomeSeer plugin

Door Sebastiaan Geplaatst op 2015-07-02 Geplaatst in Plugwise - Stretch 2.0 Getagd met HomeSeer, Plugin, Plugwise, Stretch 2.0

Website / Bron Informatie (ENG) How to install: 1. Unzip the zip file 2. Copy the database file data/Plugwise/plugwise.mdb to <your homeseer dir>/data/Plugwsie/plugwise.mdb 3. Copy the images from html/images/hspi_Plugwise to <your homeseer dir>/html/images/hspi_Plugwise 4. Copy hspi_Plugwise.dll to your homeseer dir …

Plugwise Stretch 2.0 – HomeSeer plugin Lees meer »

Plugwise Stretch 2.0 – Firmware uploaden (bootloader)

Door Sebastiaan Geplaatst op 2015-05-11 Geplaatst in Plugwise - Stretch 2.0 Getagd met Boot environment, Bootloader, Firmware, Plugwise, Stretch 2.0, TFTP, U-boot, UART, uploaden

Na wat met de smile te experimenteren en wat testwerk, gaan we nu proberen om ook op de PlugWise Stretch 2.0 nieuwe firmware te plaatsen via een tftp server. Leeswerk: 1) Wat is TFTP. 2) PlugWise Firmware downloaden. 3) UART stick …

Plugwise Stretch 2.0 – Firmware uploaden (bootloader) Lees meer »

Plugwise Stretch 2.0 – Firmware update (handmatig)

Door Sebastiaan Geplaatst op 2015-05-09 Geplaatst in Plugwise - Stretch 2.0 Getagd met handmatig, Hardware, Plugwise, Stretch 2.0, update

Ik kreeg onlangs een mailtje dat mijn PWScli programma niet meer werkt, er bleken gebruikers van de stretch te zijn die al op firmware 2.0.x zaten terwijl ik nog op 1.0.41 zat, ik vind het dan vreemd waarom wij niet …

Plugwise Stretch 2.0 – Firmware update (handmatig) Lees meer »

Plugwise Stretch 2.0 – Failsave mode via UART

Door Sebastiaan Geplaatst op 2015-02-23 Geplaatst in Plugwise - Stretch 2.0 Getagd met Failsave, Firmware, mount, Plugwise, Putty, ROOT, Stretch 2.0, UART

Ter info: Het uitproberen en experimenteren op je eigen hardware is op eigen risico!, de auteur is niet verantwoordelijk voor eventuele schade aan je hardware! Let op: Het wachtwoord voor de SSH sessie is tot op heden onbekend, als je …

Plugwise Stretch 2.0 – Failsave mode via UART Lees meer »

Plugwise Stretch 2.0 – Instellen via HTTP POST commandos

Door Sebastiaan Geplaatst op 2015-01-08 Geplaatst in Autoit3 Script, Plugwise - Stretch 2.0 Getagd met Autoit3, HTTP post, Instellen, Plugwise, Stretch 2.0

Met het voorbeeld hieronder kun je de stretch instellen zonder de “Desktop” software van plugwise nodig te hebben, het is gebaseerd op hetzelfde principe als de POST commando om een Circle te schakelen. Met het voorbeeld hieronder kun je de …

Plugwise Stretch 2.0 – Instellen via HTTP POST commandos Lees meer »

Plugwise Stretch 2.0 – Event scripting (AutoIt3)

Door Sebastiaan Geplaatst op 2015-01-08 Geplaatst in Autoit3 Script, Plugwise - Stretch 2.0 Getagd met Autoit3, Automatisch, Event scripting, Plugwise, Schakelen, Stretch 2.0

Ik heb hier een script in Autoit3 geschreven dat de Stretch kan “monitoren” via een computer, zodoende kun je je eigen “events” script bouwen. Je kan verschillende functies gebruiken zoals: – Het detecteren van het opgenomen verbruik van een plug: …

Plugwise Stretch 2.0 – Event scripting (AutoIt3) Lees meer »

Plugwise Stretch 2.0 – Commandline interface

Door Sebastiaan Geplaatst op 2014-12-26 Geplaatst in Autoit3 Script, Plugwise - Stretch 2.0 Getagd met Circles, Commandline interface, Plugwise, software, Stretch 2.0

Ik heb een programma in elkaar gezet voor het schakelen via de commandline van de PlugWise Circles met de Stretch 2.0. Zodoende kun je je eigen programma’s gebruiken (bijvoorbeeld excel, phpscript of homeseer) en zo een “shell” command gebruiken om …

Plugwise Stretch 2.0 – Commandline interface Lees meer »

Zoeken

Categorie: Plugwise – Stretch 2.0

Plugwise Stretch – Hardware van Circle modules

Plugwise Stretch 2.0 – Firmware bestanden

Plugwise Stretch 2.0 – Communicatie module (perl)

Plugwise Stretch 2.0 – HomeSeer plugin

Plugwise Stretch 2.0 – Firmware uploaden (bootloader)

Plugwise Stretch 2.0 – Firmware update (handmatig)

Plugwise Stretch 2.0 – Failsave mode via UART

Plugwise Stretch 2.0 – Instellen via HTTP POST commandos

Plugwise Stretch 2.0 – Event scripting (AutoIt3)

Plugwise Stretch 2.0 – Commandline interface