Plugwise - Stretch 2.0 Archieven - Pagina 2 van 2

Plugwise Stretch 2.0 – Linux informatie

Door Sebastiaan Geplaatst op 2014-12-25 Geplaatst in Plugwise - Stretch 2.0 Getagd met info, informatie, Linux, Plugwise, Stretch 2.0

Diverse Linux informatie vanuit de SSH bash van een Plugwise Stretch 2.0 Firmware v1.0.38

Linux stretch_xxxxxx 3.3.7 #27 Fri Dec 14 13:13:30 CET 2012 mips GNU/Linux

1	Linux stretch_xxxxxx 3.3.7 #27 Fri Dec 14 13:13:30 CET 2012 mips GNU/Linux

BusyBox v1.19.4 (2012-12-08 13:09:51 CET) built-in shell (ash)
Enter 'help' for a list of built-in commands.
 
-------------------------------------
Plugwise Stretch 1.0.38
        Based on OpenWRT
-------------------------------------

BusyBox v1.19.4 (2012-12-08 13:09:51 CET) built-in shell (ash)

Enter 'help' for a list of built-in commands.

-------------------------------------

Plugwise Stretch 1.0.38

Based on OpenWRT

-------------------------------------

system type             : Ralink RT3883   ver:1 eco:5
machine                 : Omnima EMB HPM
processor               : 0
cpu model               : MIPS 74Kc V4.12
BogoMIPS                : 249.44
wait instruction        : yes
microsecond timers      : yes
tlb_entries             : 32
extra interrupt vector  : yes
hardware watchpoint     : yes, count: 4, address/irw mask: [0x0000, 0x0f40, 0x0800, 0x0410]
ASEs implemented        : mips16 dsp
shadow register sets    : 1
kscratch registers      : 0
core                    : 0
VCED exceptions         : not available
VCEI exceptions         : not available

system type : Ralink RT3883 ver:1 eco:5

machine : Omnima EMB HPM

processor : 0

cpu model : MIPS 74Kc V4.12

BogoMIPS : 249.44

wait instruction : yes

microsecond timers : yes

tlb_entries : 32

extra interrupt vector : yes

hardware watchpoint : yes, count: 4, address/irw mask: [0x0000, 0x0f40, 0x0800, 0x0410]

ASEs implemented : mips16 dsp

shadow register sets : 1

kscratch registers : 0

core : 0

VCED exceptions : not available

VCEI exceptions : not available

6.0

6.0

DISTRIB_ID="Plugwise OpenWrt"
DISTRIB_RELEASE="6.0"
DISTRIB_REVISION="r32018"
DISTRIB_CODENAME="slp"
DISTRIB_TARGET="ramips/rt3883"
DISTRIB_DESCRIPTION="Plugwise OpenWrt SLP 6.0"

DISTRIB_ID="Plugwise OpenWrt"

DISTRIB_RELEASE="6.0"

DISTRIB_REVISION="r32018"

DISTRIB_CODENAME="slp"

DISTRIB_TARGET="ramips/rt3883"

DISTRIB_DESCRIPTION="Plugwise OpenWrt SLP 6.0"

             total         used         free       shared      buffers
Mem:         62592        39904        22688            0         4112
-/+ buffers:              35792        26800
Swap:            0            0            0

total used free shared buffers

Mem: 62592 39904 22688 0 4112

-/+ buffers: 35792 26800

Swap: 0 0 0

dev:    size   erasesize  name
mtd0: 00030000 00010000 "u-boot"
mtd1: 00010000 00010000 "config"
mtd2: 00010000 00010000 "factory"
mtd3: 00100000 00010000 "kernel"
mtd4: 00eb0000 00010000 "rootfs"
mtd5: 009a0000 00010000 "rootfs_data"
mtd6: 00fb0000 00010000 "firmware"

dev: size erasesize name

mtd0: 00030000 00010000 "u-boot"

mtd1: 00010000 00010000 "config"

mtd2: 00010000 00010000 "factory"

mtd3: 00100000 00010000 "kernel"

mtd4: 00eb0000 00010000 "rootfs"

mtd5: 009a0000 00010000 "rootfs_data"

mtd6: 00fb0000 00010000 "firmware"

MemTotal:          62592 kB
MemFree:           22920 kB
Buffers:            4112 kB
Cached:            13016 kB
SwapCached:            0 kB
Active:            20196 kB
Inactive:           8776 kB
Active(anon):      12016 kB
Inactive(anon):      116 kB
Active(file):       8180 kB
Inactive(file):     8660 kB
Unevictable:           0 kB
Mlocked:               0 kB
SwapTotal:             0 kB
SwapFree:              0 kB
Dirty:                 0 kB
Writeback:             0 kB
AnonPages:         11860 kB
Mapped:             4040 kB
Shmem:               288 kB
Slab:               6656 kB
SReclaimable:       1588 kB
SUnreclaim:         5068 kB
KernelStack:         488 kB
PageTables:          588 kB
NFS_Unstable:          0 kB
Bounce:                0 kB
WritebackTmp:          0 kB
CommitLimit:       31296 kB
Committed_AS:      20084 kB
VmallocTotal:    1048372 kB
VmallocUsed:        1240 kB
VmallocChunk:    1042200 kB

MemTotal: 62592 kB

MemFree: 22920 kB

Buffers: 4112 kB

Cached: 13016 kB

SwapCached: 0 kB

Active: 20196 kB

Inactive: 8776 kB

Active(anon): 12016 kB

Inactive(anon): 116 kB

Active(file): 8180 kB

Inactive(file): 8660 kB

Unevictable: 0 kB

Mlocked: 0 kB

SwapTotal: 0 kB

SwapFree: 0 kB

Dirty: 0 kB

Writeback: 0 kB

AnonPages: 11860 kB

Mapped: 4040 kB

Shmem: 288 kB

Slab: 6656 kB

SReclaimable: 1588 kB

SUnreclaim: 5068 kB

KernelStack: 488 kB

PageTables: 588 kB

NFS_Unstable: 0 kB

Bounce: 0 kB

WritebackTmp: 0 kB

CommitLimit: 31296 kB

Committed_AS: 20084 kB

VmallocTotal: 1048372 kB

VmallocUsed: 1240 kB

VmallocChunk: 1042200 kB

Character devices:
  1 mem
  4 ttyS
  5 /dev/tty
  5 /dev/console
  5 /dev/ptmx
 10 misc
 13 input
 90 mtd
108 ppp
128 ptm
136 pts
180 usb
188 ttyUSB
189 usb_device
 
Block devices:
259 blkext
  8 sd
 31 mtdblock
 65 sd
 66 sd
 67 sd
 68 sd
 69 sd
 70 sd
 71 sd
128 sd
129 sd
130 sd
131 sd
132 sd
133 sd
134 sd
135 sd

Character devices:

1 mem

4 ttyS

5 /dev/tty

5 /dev/console

5 /dev/ptmx

10 misc

13 input

90 mtd

108 ppp

128 ptm

136 pts

180 usb

188 ttyUSB

189 usb_device

Block devices:

259 blkext

8 sd

31 mtdblock

65 sd

66 sd

67 sd

68 sd

69 sd

70 sd

71 sd

128 sd

129 sd

130 sd

131 sd

132 sd

133 sd

134 sd

135 sd

Firmware v1.0.41

Linux stretch_xxxxxx 3.3.7 #49 Thu Feb 21 15:21:51 CET 2013 mips GNU/Linux

1	Linux stretch_xxxxxx 3.3.7 #49 Thu Feb 21 15:21:51 CET 2013 mips GNU/Linux

BusyBox v1.19.4 (2012-12-27 11:28:43 CET) built-in shell (ash)
Enter 'help' for a list of built-in commands.
 
-------------------------------------
Plugwise Stretch 1.0.41
        Based on OpenWRT
-------------------------------------

BusyBox v1.19.4 (2012-12-27 11:28:43 CET) built-in shell (ash)

Enter 'help' for a list of built-in commands.

-------------------------------------

Plugwise Stretch 1.0.41

Based on OpenWRT

-------------------------------------

6.0

6.0

DISTRIB_ID="Plugwise OpenWrt"
DISTRIB_RELEASE="6.0"
DISTRIB_REVISION="r32018"
DISTRIB_CODENAME="slp"
DISTRIB_TARGET="ramips/rt3883"
DISTRIB_DESCRIPTION="Plugwise OpenWrt SLP 6.0"

DISTRIB_ID="Plugwise OpenWrt"

DISTRIB_RELEASE="6.0"

DISTRIB_REVISION="r32018"

DISTRIB_CODENAME="slp"

DISTRIB_TARGET="ramips/rt3883"

DISTRIB_DESCRIPTION="Plugwise OpenWrt SLP 6.0"

Firmware v1.0.46

Linux stretch_xxxxxx 3.3.7 #47 Thu Aug 1 11:09:07 CEST 2013 mips GNU/Linux

1	Linux stretch_xxxxxx 3.3.7 #47 Thu Aug 1 11:09:07 CEST 2013 mips GNU/Linux

BusyBox v1.19.4 (2013-07-30 15:02:24 CEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
 
-------------------------------------
Plugwise Stretch 1.0.46
        Based on OpenWRT
-------------------------------------

BusyBox v1.19.4 (2013-07-30 15:02:24 CEST) built-in shell (ash)

Enter 'help' for a list of built-in commands.

-------------------------------------

Plugwise Stretch 1.0.46

Based on OpenWRT

-------------------------------------

6.0

6.0

DISTRIB_ID="Plugwise OpenWrt"
DISTRIB_RELEASE="6.0"
DISTRIB_REVISION="r32018"
DISTRIB_CODENAME="slp"
DISTRIB_TARGET="ramips/rt3883"
DISTRIB_DESCRIPTION="Plugwise OpenWrt SLP 6.0"

DISTRIB_ID="Plugwise OpenWrt"

DISTRIB_RELEASE="6.0"

DISTRIB_REVISION="r32018"

DISTRIB_CODENAME="slp"

DISTRIB_TARGET="ramips/rt3883"

DISTRIB_DESCRIPTION="Plugwise OpenWrt SLP 6.0"

Firmware v2.0.16

Linux stretchXXXXXX 3.6.11 #125 Wed Oct 9 12:19:45 CEST 2013 mips GNU/Linux

1	Linux stretchXXXXXX 3.6.11 #125 Wed Oct 9 12:19:45 CEST 2013 mips GNU/Linux

BusyBox v1.19.4 (2013-08-09 17:07:43 UTC) built-in shell (ash)
Enter 'help' for a list of built-in commands.
 
-------------------------------------
Plugwise Stretch 2.0.16
        Based on OpenWRT
-------------------------------------

BusyBox v1.19.4 (2013-08-09 17:07:43 UTC) built-in shell (ash)

Enter 'help' for a list of built-in commands.

-------------------------------------

Plugwise Stretch 2.0.16

Based on OpenWRT

-------------------------------------

r35013

r35013

…

Plugwise Stretch 2.0 – Linux informatie Lees meer »

Plugwise Stretch 2.0 – Schakelen met scripts (HTTP API)

Door Sebastiaan Geplaatst op 2014-11-17 Geplaatst in Autoit3 Script, PHP Script, Plugwise - Stretch 2.0, Python Script Getagd met API, Autoit3, Circles, Linux, Plugwise, Plugwise Linux, Schakelen, Scripts, Stretch, Stretch 2.0

Plugwise Stretch 2.0 API Met een packet sniffer zoals bijvoorbeeld WireShark, kan je zien wat voor gegevens verstuurd worden naar de Stretch 2.0, zo kun je achterhalen hoe de circles geschakeld worden vanuit de Stretch 2.0 Firmware 2.0.x Sinds de …

Plugwise Stretch 2.0 – Schakelen met scripts (HTTP API) Lees meer »

Plugwise Stretch 2.0 – Links en bestanden

Door Sebastiaan Geplaatst op 2014-11-17 Geplaatst in Plugwise - Stretch 2.0 Getagd met API, bestanden, links, Plugwise, Stretch 2.0

Links getest met firmware v2.0.x / v2.1.x / v2.2.x Apparaat/Module (appliance) gegevens: http://192.168.X.X/core/modules (overzicht van aangesloten apparaten op het ZigBee netwerk (module niveau) vanuit de stretch) http://192.168.X.X/core/modules;id=[MODULEID] (geeft de gegevens weer van 1 module (apparaat) in XML, [MODULEID] is het …

Plugwise Stretch 2.0 – Links en bestanden Lees meer »

Plugwise Stretch 2.0 – Boot environment

Door Sebastiaan Geplaatst op 2014-11-17 Geplaatst in Plugwise - Stretch 2.0 Getagd met Boot environment, Plugwise, Stretch 2.0

Om de boot environment van de Smile P1 weer te geven kies optie 4 in het bootmenu en type “printenv” Ps. houd de “4” ingedrukt (in PuTTY) anders werkt het niet!

RT3883 # printenv
 
bootcmd=tftp
bootdelay=2
baudrate=115200
ethaddr="00:AA:BB:CC:DD:10"
ramargs=setenv bootargs root=/dev/ram rw
addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname):$(netdev):off
addmisc=setenv bootargs $(bootargs) console=ttyS0,$(baudrate) ethaddr=$(ethaddr) panic=1
flash_self=run ramargs addip addmisc;bootm $(kernel_addr) $(ramdisk_addr)
kernel_addr=BFC40000
u-boot=u-boot.bin
load=tftp 8A100000 $(u-boot)
u_b=protect off 1:0-1;era 1:0-1;cp.b 8A100000 BC400000 $(filesize)
loadfs=tftp 8A100000 root.cramfs
u_fs=era bc540000 bc83ffff;cp.b 8A100000 BC540000 $(filesize)
test_tftp=tftp 8A100000 root.cramfs;run test_tftp
ethact=Eth0 (10/100-M)
filesize=3c0004
fileaddr=80800000
ipaddr=192.168.1.222
serverip=192.168.1.73
autostart=no
bootfile=omni-emb-hpm-squashfs-sysupgrade.bin
stdin=serial
stdout=serial
stderr=serial

RT3883 # printenv

bootcmd=tftp

bootdelay=2

baudrate=115200

ethaddr="00:AA:BB:CC:DD:10"

ramargs=setenv bootargs root=/dev/ram rw

addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname):$(netdev):off

addmisc=setenv bootargs $(bootargs) console=ttyS0,$(baudrate) ethaddr=$(ethaddr) panic=1

flash_self=run ramargs addip addmisc;bootm $(kernel_addr) $(ramdisk_addr)

kernel_addr=BFC40000

u-boot=u-boot.bin

load=tftp 8A100000 $(u-boot)

u_b=protect off 1:0-1;era 1:0-1;cp.b 8A100000 BC400000 $(filesize)

loadfs=tftp 8A100000 root.cramfs

u_fs=era bc540000 bc83ffff;cp.b 8A100000 BC540000 $(filesize)

test_tftp=tftp 8A100000 root.cramfs;run test_tftp

ethact=Eth0 (10/100-M)

filesize=3c0004

fileaddr=80800000

ipaddr=192.168.1.222

serverip=192.168.1.73

autostart=no

bootfile=omni-emb-hpm-squashfs-sysupgrade.bin

stdin=serial

stdout=serial

stderr=serial

Hele boot:

U-Boot 1.1.3 (Aug 14 2012 - 15:05:21)
 
Board: Omnima HPM DRAM:  64 MB
relocate_code Pointer at: 83fb0000
************** Init GPIO Pin Start **************
************** Init GPIO Pin Done **************
spi_wait_nsec: 30
spi device id: c2 20 18 c2 20 (2018c220)
find flash: MX25L12805D
raspi_read: from:30000 len:1000
raspi_read: from:30000 len:1000
============================================
Ralink UBoot Version: 3.5.3.0
--------------------------------------------
ASIC 3883_MP (MAC to GigaPHY Mode)
DRAM_CONF_FROM: Boot-Strapping
DRAM_TYPE: DDR2
DRAM_SIZE: 512 Mbits
DRAM_WIDTH: 16 bits
DRAM_TOTAL_WIDTH: 16 bits
TOTAL_MEMORY_SIZE: 64 MBytes
Flash component: SPI Flash
Date:Aug 14 2012  Time:15:05:21
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
 
 ##### The CPU freq = 500 MHZ ####
 estimate memory size =64 Mbytes
 
Please choose the operation:
   0: Load ucos code to SDRAM via TFTP Client.
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.
 
You choosed 4
 
raspi_read: from:40028 len:6
 
 
You choosed 4
                                                                              0
raspi_read: from:40028 len:6
.
 
4: System Enter Boot Command Line Interface.
 
U-Boot 1.1.3 (Aug 14 2012 - 15:05:21)
RT3883 # help
?       - alias for 'help'
bootm   - boot application image from memory
cp      - memory copy
erase   - erase SPI FLASH memory
go      - start application at address 'addr'
help    - print online help
loadb   - load binary file over serial line (kermit mode)
md      - memory display
mdio   - Ralink PHY register R/W command !!
mm      - memory modify (auto-incrementing)
mw      - memory write (fill)
nm      - memory modify (constant address)
printenv- print environment variables
reset   - Perform RESET of the CPU
rf      - read/write rf register
saveenv - save environment variables to persistent storage
setenv  - set environment variables
spicmd  - read/write data from/to eeprom or vtss
tftpboot- boot image via network using TFTP protocol
version - print monitor version
 
RT3883 # printenv
 
bootcmd=tftp
bootdelay=2
baudrate=115200
ethaddr="00:AA:BB:CC:DD:10"
ramargs=setenv bootargs root=/dev/ram rw
addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname):$(netdev):off
addmisc=setenv bootargs $(bootargs) console=ttyS0,$(baudrate) ethaddr=$(ethaddr) panic=1
flash_self=run ramargs addip addmisc;bootm $(kernel_addr) $(ramdisk_addr)
kernel_addr=BFC40000
u-boot=u-boot.bin
load=tftp 8A100000 $(u-boot)
u_b=protect off 1:0-1;era 1:0-1;cp.b 8A100000 BC400000 $(filesize)
loadfs=tftp 8A100000 root.cramfs
u_fs=era bc540000 bc83ffff;cp.b 8A100000 BC540000 $(filesize)
test_tftp=tftp 8A100000 root.cramfs;run test_tftp
ethact=Eth0 (10/100-M)
filesize=3c0004
fileaddr=80800000
ipaddr=192.168.1.222
serverip=192.168.1.73
autostart=no
bootfile=omni-emb-hpm-squashfs-sysupgrade.bin
stdin=serial
stdout=serial
stderr=serial

100

101

U-Boot 1.1.3 (Aug 14 2012 - 15:05:21)

Board: Omnima HPM DRAM: 64 MB

relocate_code Pointer at: 83fb0000

************** Init GPIO Pin Start **************

************** Init GPIO Pin Done **************

spi_wait_nsec: 30

spi device id: c2 20 18 c2 20 (2018c220)

find flash: MX25L12805D

raspi_read: from:30000 len:1000

============================================

Ralink UBoot Version: 3.5.3.0

--------------------------------------------

ASIC 3883_MP (MAC to GigaPHY Mode)

DRAM_CONF_FROM: Boot-Strapping

DRAM_TYPE: DDR2

DRAM_SIZE: 512 Mbits

DRAM_WIDTH: 16 bits

DRAM_TOTAL_WIDTH: 16 bits

TOTAL_MEMORY_SIZE: 64 MBytes

Flash component: SPI Flash

Date:Aug 14 2012 Time:15:05:21

============================================

icache: sets:512, ways:4, linesz:32 ,total:65536

dcache: sets:256, ways:4, linesz:32 ,total:32768

##### The CPU freq = 500 MHZ ####

estimate memory size =64 Mbytes

Please choose the operation:

0: Load ucos code to SDRAM via TFTP Client.

1: Load system code to SDRAM via TFTP.

2: Load system code then write to Flash via TFTP.

3: Boot system code via Flash (default).

4: Entr boot command line interface.

7: Load Boot Loader code then write to Flash via Serial.

9: Load Boot Loader code then write to Flash via TFTP.

You choosed 4

raspi_read: from:40028 len:6

You choosed 4

raspi_read: from:40028 len:6

4: System Enter Boot Command Line Interface.

U-Boot 1.1.3 (Aug 14 2012 - 15:05:21)

RT3883 # help

? - alias for 'help'

bootm - boot application image from memory

cp - memory copy

erase - erase SPI FLASH memory

go - start application at address 'addr'

help - print online help

loadb - load binary file over serial line (kermit mode)

md - memory display

mdio - Ralink PHY register R/W command !!

mm - memory modify (auto-incrementing)

mw - memory write (fill)

nm - memory modify (constant address)

printenv- print environment variables

reset - Perform RESET of the CPU

rf - read/write rf register

saveenv - save environment variables to persistent storage

setenv - set environment variables

spicmd - read/write data from/to eeprom or vtss

tftpboot- boot image via network using TFTP protocol

version - print monitor version

RT3883 # printenv

bootcmd=tftp

bootdelay=2

baudrate=115200

ethaddr="00:AA:BB:CC:DD:10"

ramargs=setenv bootargs root=/dev/ram rw

addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname):$(netdev):off

addmisc=setenv bootargs $(bootargs) console=ttyS0,$(baudrate) ethaddr=$(ethaddr) panic=1

flash_self=run ramargs addip addmisc;bootm $(kernel_addr) $(ramdisk_addr)

kernel_addr=BFC40000

u-boot=u-boot.bin

load=tftp 8A100000 $(u-boot)

u_b=protect off 1:0-1;era 1:0-1;cp.b 8A100000 BC400000 $(filesize)

loadfs=tftp 8A100000 root.cramfs

u_fs=era bc540000 bc83ffff;cp.b 8A100000 BC540000 $(filesize)

test_tftp=tftp 8A100000 root.cramfs;run test_tftp

ethact=Eth0 (10/100-M)

filesize=3c0004

fileaddr=80800000

ipaddr=192.168.1.222

serverip=192.168.1.73

autostart=no

bootfile=omni-emb-hpm-squashfs-sysupgrade.bin

stdin=serial

stdout=serial

stderr=serial

Plugwise Stretch 2.0 – Hardware

Door Sebastiaan Geplaatst op 2014-11-17 Geplaatst in Plugwise - Stretch 2.0 Getagd met Hardware, Plugwise, Stretch 2.0

De hardware van de Plugwise Stretch 2.0 is een: Omnima EMB HMP (SKU 16190) met een Ralink RT3662F chip. Besturingssysteem is Linux en standaard geleverd met OpenWrt / LuCi web configuration interface. Let op: De software (Openwrt) ziet de RT3662F …

Plugwise Stretch 2.0 – Hardware Lees meer »

Plugwise Stretch 2.0 – Inloggen (HTTP/TCP)

Door Sebastiaan Geplaatst op 2014-11-17 Geplaatst in Plugwise - Stretch 2.0 Getagd met inloggen, Plugwise, Stretch 2.0

Dit zijn de inloggegevens voor de Stretch 2.0 met firmare username = stretch password = stretch-id (8 karaktercode) Direct inloggen via de URL op de smile via http, gebruik: http://stretch:[STRETCH_ID]@192.168.X.X/smartmeter/modules [STRETCH_ID] = smile-id (8 karaktercode) Ps. Dit wordt alleen in Internet …

Plugwise Stretch 2.0 – Inloggen (HTTP/TCP) Lees meer »

Plugwise Stretch 2.0 – Verbinden via UART TTL

Door Sebastiaan Geplaatst op 2014-11-17 Geplaatst in Plugwise - Stretch 2.0 Getagd met Plugwise, Stretch 2.0, UART TTL

Hier volgt een kleine handleiding om de Plugwise Stretch 2.0 aan te sluiten via een UART TTL seriële verbinding. Wat heb je nodig? 1) UART > USB stick. 2) PuTTy telnet software. Pinout: Volgens de handleiding van Omnima MiniEMBWiFi is …

Plugwise Stretch 2.0 – Verbinden via UART TTL Lees meer »

Zoeken

Categorie: Plugwise – Stretch 2.0

Plugwise Stretch 2.0 – Linux informatie

Plugwise Stretch 2.0 – Schakelen met scripts (HTTP API)

Plugwise Stretch 2.0 – Links en bestanden

Plugwise Stretch 2.0 – Boot environment

Plugwise Stretch 2.0 – Hardware

Plugwise Stretch 2.0 – Inloggen (HTTP/TCP)

Plugwise Stretch 2.0 – Verbinden via UART TTL