UART Archieven - Pagina 2 van 3 - DomoticX Knowledge Center

Samsung SMT-6010E – Boot LOG (UART)

Door Sebastiaan Geplaatst op 2016-02-21 Geplaatst in Samsung Getagd met Bootlog, Box, decoder, Samsung, SMT-6010E, UART

BOOT LOG (UART):

Success1 registering the  Video DAC devices for board: 1300, daughter board: 0
Success2 registering the  Video DAC devices for board: 1300, daughter board: 0
Success3 registering the  Video DAC devices for board: 1300, daughter board: 0
[cyg_net_init] Init: mbinit(0x00000000)
[cyg_net_init] Init: cyg_net_init_devs(0x00000000)
Init device 'rltk8139_eth0'
[cyg_net_init] Init: loopattach(0x00000000)
[cyg_net_init] Init: ifinit(0x00000000)
[cyg_net_init] Init: domaininit(0x00000000)
[cyg_net_init] Init: cyg_net_add_domain(0x803afae0)
New domain internet at 0x00000000
[cyg_net_init] Init: cyg_net_add_domain(0x803aea60)
New domain route at 0x00000000
[cyg_net_init] Init: call_route_init(0x00000000)
[cyg_net_init] Done
*************************
* Bootrom Version       *
* V_STB_BT_01_02_050418 *
*************************
pciVIAInit
imageDisplay
Display Refresh Video Output example.
etiDefaultMemPool 0x87efc000 , start 0x80000000 size 0x8000000 hiMemGap 0x104000
xOffset 80 yOffset 48 dstBytesPerPixel 2 imageBmpWidth 640
CXA2161R status : d8
CXA2161R status : d8
Press <CANCEL> remote key to start net booting....
hmpv_read_fcnt
start time in 23eab437 cycles
Doc Booting....
flRegisterSAFTL: start
flRegisterSAFTL: end
Media Size = 32 Mbytes
 
Note: Searching for the media header.
      As a result a few H/W protection error messages might be reported.
 
ERROR in read_Seq: M512_checkAndFixAccessError:Protection error occurred.
ERROR in read_Seq: M512_checkAndFixAccessError:Protection error occurred.
ERROR in read_Seq: M512_checkAndFixAccessError:Protection error occurred.
ERROR in read_Seq: M512_checkAndFixAccessError:Protection error occurred.
 
Note: header was found - end of media header search.
 
DALN: PC=0x8009938c, RP=0x800ff560, addr=0x80a19f39: 2 byte load r60
START WITH BANK0
imageversion : 0
START TIME : 26940493
bdkReadBlock has Completed Succefully
CheckSignature returned 0, nds signature passed
END TIME : b156d10e
Read done in 8d7d1a30 cycles
Start Booting.... address from [82217820]
00:0a:0 Class 0200: 10ec:8139 0:0x1000[256]I 1:0x10000000[256]M IRQ 9
00:0c:0 Class 0601: 1106:0686
00:0c:1 Class 0101: 1106:0571 4:0x1100[16]I
00:0c:2 Class 0c03: 1106:3038 4:0x1120[32]I IRQ 16
00:0c:4 Class 0000: 1106:3057
pciDolphinFixup: 10ec:8139 IRQ pin A-->B IRQ 10
pciDolphinFixup: 1106:3038 VIA device: IRQ 42 (i8259 IRQ 5)
Linux version 2.2.20 (root@MF-DEV-SSBUILD01) (ecc version v6.0_6127) #1 Wed Dec 15 13:10:43 CET 2010
CPU frequency: 297 MHz
Mem frequency: 118 MHz
Calibrating delay loop... 296.55 BogoMIPS
Memory: 96128k/130032k available (2736k kernel code, 1072k data, 400k reserved)
Dentry hash table entries: 16384 (order 3, 128k)
Buffer cache hash table entries: 524288 (order 7, 2048k)
Page cache hash table entries: 8192 (order 1, 32k)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
TCP: Hash tables configured (ehash 524288 bhash 65536)
Serial driver version 4.27 with no serial options enabled
ttyS00 at 0x03f8 (irq = 41) is a 16550A
ttyS01 at 0x02f8 (irq = 40) is a 16550A
pty: 256 Unix98 ptys configured
RAM disk driver initialized:  16 RAM disks of 29696K size
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 29696 blocks [1 disk] into ram disk... done.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb.c: registered new driver hid
mice: PS/2 mouse device common for all mice
usb-uhci.c: $Revision: 1.2 $ time 13:11:06 Dec 15 2010
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0x1120, IRQ 42
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
usb.c: USB new device connect, assigned device number 1
Product: USB UHCI Root Hub
SerialNumber: 1120
hub.c: USB hub found
hub.c: 2 ports detected
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 128k freed
Using /lib/modules/2.2.20/block/doc.o
fl: TrueFFS driver 621.41
flRegisterComponents: fFound:01
fl: 1 device(s) found
fl: Registered module at major 62
Partition check:
 fla: fla1
fl: Device 0x0 size 0x1028000 sectors 0x8140
fl:     partition 0x1 size 0x1024c00
 fla: fla1
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
EXT2-fs error (device fl(62,1)): ext2_check_blocks_bitmap: Wrong free blocks count for group 0, stored = 2798, counted = 2800
EXT2-fs error (device fl(62,1)): ext2_check_blocks_bitmap: Wrong free blocks count in super block, stored = 10727, counted = 10729
EXT2-fs error (device fl(62,1)): ext2_check_inodes_bitmap: Wrong free inodes count in group 0, stored = 2039, counted = 2041
EXT2-fs error (device fl(62,1)): ext2_check_inodes_bitmap: Wrong free inodes count in super block, stored = 4111, counted = 4113
grep: /var/run/rc.pids: No such file or directory
test: 0: unknown operand
ifconfig: face: error fetching interface information: Device not found
 
Using /lib/modules/2.2.20/8139too.o
PCI: Increasing latency timer of device 00:50 to 64
eth0: 8139too Fast Ethernet driver 0.9.18-2.2
eth0: Samsung Electronics SMT-6000E, YSU v1.2 <sukun.yoon@samsung.com>
eth0: RealTek RTL8139 Fast Ethernet board found at 0x1000, IRQ 10
eth0: Chip is 'RTL-8139C' - MAC address '00:00:f0:ef:7e:56'.
ifconfig: face: error fetching interface information: Device not found
 
60: old priority 0, new priority 7
eth0: Setting half-duplex based on auto-negotiated partner ability 0000.
Using /lib/modules/2.2.20/saa7128/saa7128.o
Loading Saa7128 Color Bar Test Module
Saa7128color: Device registered with Major Number = 0
Using /lib/modules/2.2.20/saa7128/cxa2161r.o
^ALoading Cxa2161r Scart Switch Test Module
Cxa2161rScart: Device registered with Major Number = 0
connect: Network is unreachable
cat: /proc/bus/usb/devices: No such file or directory
rm: cannot remove `/wfs/run': No such file or directory
Login: killall: Evo: no process killed
ifconfig: face: error fetching interface information: Device not found
 
Using /lib/modules/2.2.20/pageCluster.o
Using /lib/modules/2.2.20/KernelEvents.o
Using /lib/modules/2.2.20/processInfo.o
Using /lib/modules/2.2.20/ProcessInfoDrv.o
Using /lib/modules/2.2.20/EventDrv.o
Using /lib/modules/2.2.20/PageClusterDrv.o
^[[5~Using /lib/modules/2.2.20/noncoregpDev.o
Using /lib/modules/2.2.20/boardSupportDev.o
Success1 registering the  Video DAC devices for board: 1300, daughter board: 0
Success2 registering the  Video DAC devices for board: 1300, daughter board: 0
Success3 registering the  Video DAC devices for board: 1300, daughter board: 0
Using /lib/modules/2.2.20/dmaBuffers.o
Using /lib/modules/2.2.20/streaming.o
Using /lib/modules/2.2.20/mediaDev.o
Jump starting VLX processor In 6.0 mode.
Vlx processor started successfully (vlxStatus 0x2).
Using /lib/modules/2.2.20/ScrDrv.o
Using /lib/modules/2.2.20/AoutDrv.o
Using /lib/modules/2.2.20/DrcDrv.o
Using /lib/modules/2.2.20/DmaBufferDrv.o
Using /lib/modules/2.2.20/cs4341/cs4341Control.o
Using /lib/modules/2.2.20/IrDrv.o
REAL POOL 0x2d00008 to 0x2d00008. Heap at 0x1075524
REAL MALLOC 0x2d00008
REAL POOL 0x2d00008 to 0x2d00028. Heap at 0x1075524
REAL MALLOC 0x2d00028
REAL POOL 0x2d00008 to 0x2d00038. Heap at 0x1075524
REAL MALLOC 0x2d00038
REAL FREE (nil)
REAL POOL 0x2d00008 to 0x2d00130. Heap at 0x1075524
REAL MALLOC 0x2d00130
REAL POOL 0x2d00008 to 0x2aab0008. Heap at 0x1075524
REAL MALLOC 0x2aab0008
REAL POOL 0x2d00008 to 0x2aab0008. Heap at 0x1075524
REAL MALLOC 0x2d00960
Saa7128color : Device Open (254, 0)
Saa7128color: Opened Value 0
Enter SamsungPlayer:0
TVmode select: 4:3 TV
^[[5~Login: IIS audclk = 1
audclk = 1
DrcDrv: Output -> PAL Interlaced 720 x 576 @ 25Hz
 
  Primary input:   Enabled
  Secondary input: Enabled
  Graphics input:  Enabled
  gfxFormat:       800
  alphaStream:     0
WARNING: Unable to utilize DMA pool. Defaulted to alloc for 1658880 bytes. This is OK during Evo init.
Cxa2161rScart : Device Open (252, 0)
Cxa2161rScart: Opened Value 0
 
I2C_ADDR - DATA1, DATA2, DATA3, DATA4, DATA5, DATA6, DATA7
  [90]       86 ,   80,    00 ,   33 ,   00 ,   0b ,   ef
 
I2C_ADDR - DATA1, DATA2, DATA3, DATA4, DATA5, DATA6, DATA7
  [90]       86 ,   80,    00 ,   33 ,   00 ,   0b ,   ef
                        ZCS POD     S/D FNC_VCR
                 7 - 6 - 5 - 4 - 3 - 2 - 1 - 0
CXA2161R STATUS: 1 - 1 - 1 - 1 - 1 - 0 - 0 - 0

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

147

148

149

150

151

152

153

154

155

156

157

158

159

160

161

162

163

164

165

166

167

168

169

170

171

172

173

174

175

176

177

178

179

180

181

182

183

184

185

186

187

188

189

190

191

192

193

194

195

196

197

198

199

200

Success1 registering the Video DAC devices for board: 1300, daughter board: 0

Success2 registering the Video DAC devices for board: 1300, daughter board: 0

Success3 registering the Video DAC devices for board: 1300, daughter board: 0

[cyg_net_init] Init: mbinit(0x00000000)

[cyg_net_init] Init: cyg_net_init_devs(0x00000000)

Init device 'rltk8139_eth0'

[cyg_net_init] Init: loopattach(0x00000000)

[cyg_net_init] Init: ifinit(0x00000000)

[cyg_net_init] Init: domaininit(0x00000000)

[cyg_net_init] Init: cyg_net_add_domain(0x803afae0)

New domain internet at 0x00000000

[cyg_net_init] Init: cyg_net_add_domain(0x803aea60)

New domain route at 0x00000000

[cyg_net_init] Init: call_route_init(0x00000000)

[cyg_net_init] Done

*************************

* Bootrom Version *

* V_STB_BT_01_02_050418 *

*************************

pciVIAInit

imageDisplay

Display Refresh Video Output example.

etiDefaultMemPool 0x87efc000 , start 0x80000000 size 0x8000000 hiMemGap 0x104000

xOffset 80 yOffset 48 dstBytesPerPixel 2 imageBmpWidth 640

CXA2161R status : d8

Press <CANCEL> remote key to start net booting....

hmpv_read_fcnt

start time in 23eab437 cycles

Doc Booting....

flRegisterSAFTL: start

flRegisterSAFTL: end

Media Size = 32 Mbytes

Note: Searching for the media header.

As a result a few H/W protection error messages might be reported.

ERROR in read_Seq: M512_checkAndFixAccessError:Protection error occurred.

Note: header was found - end of media header search.

DALN: PC=0x8009938c, RP=0x800ff560, addr=0x80a19f39: 2 byte load r60

START WITH BANK0

imageversion : 0

START TIME : 26940493

bdkReadBlock has Completed Succefully

CheckSignature returned 0, nds signature passed

END TIME : b156d10e

Read done in 8d7d1a30 cycles

Start Booting.... address from [82217820]

00:0a:0 Class 0200: 10ec:8139 0:0x1000[256]I 1:0x10000000[256]M IRQ 9

00:0c:0 Class 0601: 1106:0686

00:0c:1 Class 0101: 1106:0571 4:0x1100[16]I

00:0c:2 Class 0c03: 1106:3038 4:0x1120[32]I IRQ 16

00:0c:4 Class 0000: 1106:3057

pciDolphinFixup: 10ec:8139 IRQ pin A-->B IRQ 10

pciDolphinFixup: 1106:3038 VIA device: IRQ 42 (i8259 IRQ 5)

Linux version 2.2.20 (root@MF-DEV-SSBUILD01) (ecc version v6.0_6127) #1 Wed Dec 15 13:10:43 CET 2010

CPU frequency: 297 MHz

Mem frequency: 118 MHz

Calibrating delay loop... 296.55 BogoMIPS

Memory: 96128k/130032k available (2736k kernel code, 1072k data, 400k reserved)

Dentry hash table entries: 16384 (order 3, 128k)

Buffer cache hash table entries: 524288 (order 7, 2048k)

Page cache hash table entries: 8192 (order 1, 32k)

POSIX conformance testing by UNIFIX

PCI: Probing PCI hardware

Linux NET4.0 for Linux 2.2

Based upon Swansea University Computer Society NET3.039

NET4: Unix domain sockets 1.0 for Linux NET4.0.

NET4: Linux TCP/IP 1.0 for NET4.0

IP Protocols: ICMP, UDP, TCP, IGMP

TCP: Hash tables configured (ehash 524288 bhash 65536)

Serial driver version 4.27 with no serial options enabled

ttyS00 at 0x03f8 (irq = 41) is a 16550A

ttyS01 at 0x02f8 (irq = 40) is a 16550A

pty: 256 Unix98 ptys configured

RAM disk driver initialized: 16 RAM disks of 29696K size

RAMDISK: ext2 filesystem found at block 0

RAMDISK: Loading 29696 blocks [1 disk] into ram disk... done.

usb.c: registered new driver usbdevfs

usb.c: registered new driver hub

usb.c: registered new driver hid

mice: PS/2 mouse device common for all mice

usb-uhci.c: $Revision: 1.2 $ time 13:11:06 Dec 15 2010

usb-uhci.c: High bandwidth mode enabled

usb-uhci.c: USB UHCI at I/O 0x1120, IRQ 42

usb-uhci.c: Detected 2 ports

usb.c: new USB bus registered, assigned bus number 1

usb.c: USB new device connect, assigned device number 1

Product: USB UHCI Root Hub

SerialNumber: 1120

hub.c: USB hub found

hub.c: 2 ports detected

VFS: Mounted root (ext2 filesystem).

Freeing unused kernel memory: 128k freed

Using /lib/modules/2.2.20/block/doc.o

fl: TrueFFS driver 621.41

flRegisterComponents: fFound:01

fl: 1 device(s) found

fl: Registered module at major 62

Partition check:

fla: fla1

fl: Device 0x0 size 0x1028000 sectors 0x8140

fl: partition 0x1 size 0x1024c00

fla: fla1

EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended

EXT2-fs error (device fl(62,1)): ext2_check_blocks_bitmap: Wrong free blocks count for group 0, stored = 2798, counted = 2800

EXT2-fs error (device fl(62,1)): ext2_check_blocks_bitmap: Wrong free blocks count in super block, stored = 10727, counted = 10729

EXT2-fs error (device fl(62,1)): ext2_check_inodes_bitmap: Wrong free inodes count in group 0, stored = 2039, counted = 2041

EXT2-fs error (device fl(62,1)): ext2_check_inodes_bitmap: Wrong free inodes count in super block, stored = 4111, counted = 4113

grep: /var/run/rc.pids: No such file or directory

test: 0: unknown operand

ifconfig: face: error fetching interface information: Device not found

Using /lib/modules/2.2.20/8139too.o

PCI: Increasing latency timer of device 00:50 to 64

eth0: 8139too Fast Ethernet driver 0.9.18-2.2

eth0: Samsung Electronics SMT-6000E, YSU v1.2 <sukun.yoon@samsung.com>

eth0: RealTek RTL8139 Fast Ethernet board found at 0x1000, IRQ 10

eth0: Chip is 'RTL-8139C' - MAC address '00:00:f0:ef:7e:56'.

ifconfig: face: error fetching interface information: Device not found

60: old priority 0, new priority 7

eth0: Setting half-duplex based on auto-negotiated partner ability 0000.

Using /lib/modules/2.2.20/saa7128/saa7128.o

Loading Saa7128 Color Bar Test Module

Saa7128color: Device registered with Major Number = 0

Using /lib/modules/2.2.20/saa7128/cxa2161r.o

^ALoading Cxa2161r Scart Switch Test Module

Cxa2161rScart: Device registered with Major Number = 0

connect: Network is unreachable

cat: /proc/bus/usb/devices: No such file or directory

rm: cannot remove `/wfs/run': No such file or directory

ifconfig: face: error fetching interface information: Device not found

Using /lib/modules/2.2.20/pageCluster.o

Using /lib/modules/2.2.20/KernelEvents.o

Using /lib/modules/2.2.20/processInfo.o

Using /lib/modules/2.2.20/ProcessInfoDrv.o

Using /lib/modules/2.2.20/EventDrv.o

Using /lib/modules/2.2.20/PageClusterDrv.o

^[[5~Using /lib/modules/2.2.20/noncoregpDev.o

Using /lib/modules/2.2.20/boardSupportDev.o

Success1 registering the Video DAC devices for board: 1300, daughter board: 0

Success2 registering the Video DAC devices for board: 1300, daughter board: 0

Success3 registering the Video DAC devices for board: 1300, daughter board: 0

Using /lib/modules/2.2.20/dmaBuffers.o

Using /lib/modules/2.2.20/streaming.o

Using /lib/modules/2.2.20/mediaDev.o

Jump starting VLX processor In 6.0 mode.

Vlx processor started successfully (vlxStatus 0x2).

Using /lib/modules/2.2.20/ScrDrv.o

Using /lib/modules/2.2.20/AoutDrv.o

Using /lib/modules/2.2.20/DrcDrv.o

Using /lib/modules/2.2.20/DmaBufferDrv.o

Using /lib/modules/2.2.20/cs4341/cs4341Control.o

Using /lib/modules/2.2.20/IrDrv.o

REAL POOL 0x2d00008 to 0x2d00008. Heap at 0x1075524

REAL MALLOC 0x2d00008

REAL POOL 0x2d00008 to 0x2d00028. Heap at 0x1075524

REAL MALLOC 0x2d00028

REAL POOL 0x2d00008 to 0x2d00038. Heap at 0x1075524

REAL MALLOC 0x2d00038

REAL FREE (nil)

REAL POOL 0x2d00008 to 0x2d00130. Heap at 0x1075524

REAL MALLOC 0x2d00130

REAL POOL 0x2d00008 to 0x2aab0008. Heap at 0x1075524

REAL MALLOC 0x2aab0008

REAL POOL 0x2d00008 to 0x2aab0008. Heap at 0x1075524

REAL MALLOC 0x2d00960

Saa7128color : Device Open (254, 0)

Saa7128color: Opened Value 0

Enter SamsungPlayer:0

TVmode select: 4:3 TV

^[[5~Login: IIS audclk = 1

audclk = 1

DrcDrv: Output -> PAL Interlaced 720 x 576 @ 25Hz

Primary input: Enabled

Secondary input: Enabled

Graphics input: Enabled

gfxFormat: 800

alphaStream: 0

WARNING: Unable to utilize DMA pool. Defaulted to alloc for 1658880 bytes. This is OK during Evo init.

Cxa2161rScart : Device Open (252, 0)

Cxa2161rScart: Opened Value 0

I2C_ADDR - DATA1, DATA2, DATA3, DATA4, DATA5, DATA6, DATA7

[90] 86 , 80, 00 , 33 , 00 , 0b , ef

I2C_ADDR - DATA1, DATA2, DATA3, DATA4, DATA5, DATA6, DATA7

[90] 86 , 80, 00 , 33 , 00 , 0b , ef

ZCS POD S/D FNC_VCR

7 - 6 - 5 - 4 - 3 - 2 - 1 - 0

CXA2161R STATUS: 1 - 1 - 1 - 1 - 1 - 0 - 0 - 0

KPN Experia Box (Arcadyan ARV7519) – UART aansluiting

Door Sebastiaan Geplaatst op 2016-01-14 Geplaatst in KPN Getagd met Arcadyan ARV7519, Bootlog, Experia Box, Firmware, KPN, PW22, Router, UART, WLAN

Loshalen De KPN Experia Box (Arcadyan ARV7519) is makkelijk los te maken, je moet de 2 schroefjes losdraaien aan de achterkant, en dan kan je hem zo open “klikken”. UART aansluiting Ps. sluit de RxD van de TTL USB stick …

KPN Experia Box (Arcadyan ARV7519) – UART aansluiting Lees meer »

KPN Experia Box (Arcadyan ARV7519) – Bootlog via UART

Door Sebastiaan Geplaatst op 2016-01-13 Geplaatst in KPN Getagd met Arcadyan ARV7519, Bootlog, Experia Box, Firmware, KPN, PW22, Router, UART, WLAN

Bootlog via UART Dit is de bootlog bij het opstarten via de UART seriele verbinding op de printplaat.

ROM VER: 1.0.3
CFG 01
Read EEPROMX
 X



=======================================================================
Wireless ADSL Gateway DANUBE Loader v2.00.12 build Jan 17 2011 17:15:51
                    Arcadyan Technology Corporation
=======================================================================
EON EN29LV640L top boot 16-bit mode found

Copying boot params.....DONE


Press Space Bar 3 times to enter command mode ...
Flash Checking [0] Passed.
Image[1] at 0xb0100000, len:1868317, type:0
Image[2] at 0xb02c8400, len:6928, type:10
Image[3] at 0xb02ca000, len:224436, type:11
Image[4] at 0xb0301000, len:227009, type:12
Image[5] at 0xb0338800, len:168592, type:50
Image[6] at 0xb0361c00, len:452618, type:90
Firmware image at 0, ART image at -1

Run-up Normal Firmware...

Unzipping firmware [0(5)] at 0x80002000 ... [ZIP 3] [ZIP 1]  done
Run-time code running ...

In c_entry() function ...
install_exception
Co config = 80008483
[INIT] Interrupt ...
##### _ftext      = 0x80002000
##### _fdata      = 0x80723F10
##### __bss_start = 0x807F6A94
##### end         = 0x8330B280
allocate_memory_after_end> len 863108, ptr 0x83313280
##### Backup Data from 0x80723F10 to 0x83313280~0x833E5E04 len 863108
##### Backup Data completed
##### Backup Data verified
EON EN29LV640L top boot 16-bit mode found
new bootcode format
[GPIO FLOW] SetGpio() Begin ..
gptu: totally 6 16-bit timers/counters
Init timer = 0
[GPIO FLOW] SetGpio() End.
[INIT] System Log Pool startup ...
[INIT] MTinitialize ..
[INIT] usrclk
CPU Clock 333333334 Hz
mips_counter_frequency:166666667
r4k_offset: 00028b0a(166666)
init_US_counter : time1 = 260456 , time2 = 40260479, diff 40000023
US_counter = 48
 cnt1 40987750 cnt2 40990007, diff 2257
Runtime code version: 01.01.121
System startup...
[INIT] Memory COLOR 0, 3000000 bytes ..
[INIT] Memory COLOR 1, 262144 bytes ..
[INIT] Memory COLOR 2, 4565152 bytes ..
EON EN29LV640L top boot 16-bit mode found

ROM VER: 1.0.3

CFG 01

Read EEPROMX

=======================================================================

Wireless ADSL Gateway DANUBE Loader v2.00.12 build Jan 17 2011 17:15:51

Arcadyan Technology Corporation

=======================================================================

EON EN29LV640L top boot 16-bit mode found

Copying boot params.....DONE

Press Space Bar 3 times to enter command mode ...

Flash Checking [0] Passed.

Image[1] at 0xb0100000, len:1868317, type:0

Image[2] at 0xb02c8400, len:6928, type:10

Image[3] at 0xb02ca000, len:224436, type:11

Image[4] at 0xb0301000, len:227009, type:12

Image[5] at 0xb0338800, len:168592, type:50

Image[6] at 0xb0361c00, len:452618, type:90

Firmware image at 0, ART image at -1

Run-up Normal Firmware...

Unzipping firmware [0(5)] at 0x80002000 ... [ZIP 3] [ZIP 1] done

Run-time code running ...

In c_entry() function ...

install_exception

Co config = 80008483

[INIT] Interrupt ...

##### _ftext = 0x80002000

##### _fdata = 0x80723F10

##### __bss_start = 0x807F6A94

##### end = 0x8330B280

allocate_memory_after_end> len 863108, ptr 0x83313280

##### Backup Data from 0x80723F10 to 0x83313280~0x833E5E04 len 863108

##### Backup Data completed

##### Backup Data verified

EON EN29LV640L top boot 16-bit mode found

new bootcode format

[GPIO FLOW] SetGpio() Begin ..

gptu: totally 6 16-bit timers/counters

Init timer = 0

[GPIO FLOW] SetGpio() End.

[INIT] System Log Pool startup ...

[INIT] MTinitialize ..

[INIT] usrclk

CPU Clock 333333334 Hz

mips_counter_frequency:166666667

r4k_offset: 00028b0a(166666)

init_US_counter : time1 = 260456 , time2 = 40260479, diff 40000023

US_counter = 48

cnt1 40987750 cnt2 40990007, diff 2257

Runtime code version: 01.01.121

System startup...

[INIT] Memory COLOR 0, 3000000 bytes ..

[INIT] Memory COLOR 1, 262144 bytes ..

[INIT] Memory COLOR 2, 4565152 bytes ..

EON EN29LV640L top boot 16-bit mode found

RESET knop ingedrukt This is the bootlog when booting with the reset button pressed. It also launches a webserver at 192.168.2.254. …

KPN Experia Box (Arcadyan ARV7519) – Bootlog via UART Lees meer »

PL2303 USB to UART Bridge Drivers (Windows)

Door Sebastiaan Geplaatst op 2015-05-29 Geplaatst in Stuurprogramma's Getagd met Bridge, Drivers, PL2303, Prolific, Serial, stuurprogramma, UART, USB

Windows 10 Indien men een PL2303 HXA chip gebruikt (nog steeds volop in omloop) wordt deze niet meer ondersteunt door Windows 10, je krijgt dan de volgende melding te zien: Om dit op te lossen is een driver nodig met …

PL2303 USB to UART Bridge Drivers (Windows) Lees meer »

Plugwise Stretch 2.0 – Firmware uploaden (bootloader)

Door Sebastiaan Geplaatst op 2015-05-11 Geplaatst in Plugwise - Stretch 2.0 Getagd met Boot environment, Bootloader, Firmware, Plugwise, Stretch 2.0, TFTP, U-boot, UART, uploaden

Na wat met de smile te experimenteren en wat testwerk, gaan we nu proberen om ook op de PlugWise Stretch 2.0 nieuwe firmware te plaatsen via een tftp server. Leeswerk: 1) Wat is TFTP. 2) PlugWise Firmware downloaden. 3) UART stick …

Plugwise Stretch 2.0 – Firmware uploaden (bootloader) Lees meer »

Plugwise Smile P1 – Firmware uploaden (bootloader)

Door Sebastiaan Geplaatst op 2015-05-10 Geplaatst in Plugwise - Smile P1 Getagd met Boot environment, Bootloader, Firmware, Plugwise, Smile P1, TFTP, U-boot, UART, uploaden

Na enige tijd stoeien, trial & error en veel leeswerk, is het me gelukt om via U-boot een firmware image te uploaden op een PlugWise Smile via een tftp server. Leeswerk: 1) Wat is TFTP. 2) PlugWise Firmware downloaden. 3) UART stick …

Plugwise Smile P1 – Firmware uploaden (bootloader) Lees meer »

Fritz!Box Fon WLAN 7170 – Firmware I/O via bootloader

Door Sebastiaan Geplaatst op 2015-04-18 Geplaatst in FRITZ!Box Getagd met 7170, Backup, Bootloader, Firmware, Fon, Fritz!Box, Router, UART, Wireless, WLAN

Fritz!Box Fon WLAN 7170 Router Zodra je via ftp bent ingelogd in de bootloader kun je altijd het flash geheugen herstellen doormiddel van een firmware image. Echter werkt de standaard ftp client van windows NIET op de Fritz!Box, gebruik daarvoor bijvoorbeeld NcFTP. Wat …

Fritz!Box Fon WLAN 7170 – Firmware I/O via bootloader Lees meer »

Fritz!Box Fon WLAN 7170 – Firmware I/O via telnet

Door Sebastiaan Geplaatst op 2015-04-17 Geplaatst in FRITZ!Box Getagd met 7170, Backup, Firmware, Fon, Fritz!Box, Router, UART, Wireless, WLAN

Fritz!Box Fon WLAN 7170 Router Firmware backup via telnet Zodra je via telnet bent ingelogd kun je de partities weergeven met het commando cat proc/mtd :

dev:    size   erasesize  name
mtd0: 00800000 00010000 "phys_mapped_flash"
mtd1: 006c8d00 00010000 "filesystem"
mtd2: 00770000 00010000 "kernel"
mtd3: 00010000 00010000 "bootloader"
mtd4: 00040000 00010000 "tffs (1)"
mtd5: 00040000 00010000 "tffs (2)"
mtd6: 00130000 00010000 "jffs2"
mtd7: 00640000 00010000 "Kernel without jffs2"

dev: size erasesize name

mtd0: 00800000 00010000 "phys_mapped_flash"

mtd1: 006c8d00 00010000 "filesystem"

mtd2: 00770000 00010000 "kernel"

mtd3: 00010000 00010000 "bootloader"

mtd4: 00040000 00010000 "tffs (1)"

mtd5: 00040000 00010000 "tffs (2)"

mtd6: 00130000 00010000 "jffs2"

mtd7: 00640000 00010000 "Kernel without jffs2"

Je kan deze ook zien in de dev folder met het commando ls /dev : Een backup maken gaat …

Fritz!Box Fon WLAN 7170 – Firmware I/O via telnet Lees meer »

Fritz!Box Fon WLAN 7170 – UART / JTAG aansluiting

Door Sebastiaan Geplaatst op 2015-04-15 Geplaatst in FRITZ!Box Getagd met 7170, Firmware, Fon, Fritz!Box, JTAG, Router, UART, Wireless, WLAN

Fritz!Box Fon WLAN 7170 Router Loshalen De Fritz!Box is makkelijk los te maken, je moet met een kleine schroevendraaier de 4 pinnetjes onder aan de zijkanten indrukken, dan klikt hij zo los. UART aansluiting Een ezelsbruggetje: Bij de Fritz!Box is …

Fritz!Box Fon WLAN 7170 – UART / JTAG aansluiting Lees meer »

Fritz!Box Fon WLAN 7170 – Bootlog via UART

Door Sebastiaan Geplaatst op 2015-04-15 Geplaatst in FRITZ!Box Getagd met 7170, Bootlog, Firmware, Fon, Fritz!Box, Router, UART, Wireless, WLAN

Fritz!Box Fon WLAN 7170 Router Bootlog via UART Dit is de bootlog bij het opstarten via de UART seriele verbinding op de printplaat

(AVM) EVA Revision: 1.347 Version: 1347
(C) Copyright 2005 AVM Date: Sep 20 2007 Time: 11:14:07 (0) 2 0x0-0x41F

[FLASH:] SPANSION Top-MirrorBit-Flash 8MB 32 Bytes WriteBuffer
[FLASH:](Eraseregion [0] 127 sectors a 64kB)
[FLASH:](Eraseregion [1] 8 sectors a 8kB)
[SYSTEM:] OHIO on 211MHz/125MHz

Eva_AVM >AVM decompress Kernel:
..................executeProgram on 0x941EB000
[ohio_pre_init] System Clk = 62500000 Hz

LINUX started...
Linux version 2.6.13.1-ohio (1699) (gcc-Version 3.4.6) #1 Thu Jun 25 13:14:17 CEST 2009
memsize=32 MByte
flashsize=8 MByte
&_end=0x9423ee74 PFN_ALIGN(&_end)=0x9423f000 CPHYSADDR(PFN_ALIGN(&_end))=0x1423f000 memsize=0x2000000
CPU revision is: 00018448
[ohio_gpio_init]
Determined physical RAM map:
 memory: 0023f000 @ 14000000 (reserved)
 memory: 01dc1000 @ 1423f000 (usable)
On node 0 totalpages: 8192
[alloc_node_mem_map] reduce size from 2883616 Bytes to  262176 Bytes
[alloc_node_mem_map]: (org) sizeof(mem_map) = 262176 mem_map=0x94242000-0x94282020
[alloc_node_mem_map]: sizeof(mem_map) = 2883616 mem_map=0x93fc2000-0x94282020
zone=0 zone_size[j]=0x90112
realsize=8192
  DMA zone: 8192 pages, LIFO batch:3
zone=1 zone_size[j]=0x0
realsize=0
  Normal zone: 0 pages, LIFO batch:1
zone=2 zone_size[j]=0x0
realsize=0
  HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line:  console=ttyS0,38400n8r
[ld_mmu_r4xx0] memcpy((void *)(CAC_BASE   + 0x100), &except_vec2_generic, 0x30)
Primary instruction cache 16kB, physically tagged, 4-way, linesize 16 bytes.
Primary data cache 8kB, 4-way, linesize 16 bytes.
Synthesized TLB refill handler (20 instructions). Base=0x9420578c
TLB synthesizer field overflow (simm)
Synthesized TLB load handler fastpath (34 instructions) Base=0x94208620.
TLB synthesizer field overflow (simm)
Synthesized TLB store handler fastpath (34 instructions) Base=0x94208820.
TLB synthesizer field overflow (simm)
Synthesized TLB modify handler fastpath (33 instructions) Base=0x94208a20.
PID hash table entries: 256 (order: 8, 4096 bytes)
CPU frequency 211.97 MHz
Using 105.984 MHz high precision timer.
[setup_irq]: irq 255 irqaction->handler 0x940430c0 (no_action+0x0/0x8 )
[register_console] enable commandline console 0
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 30092k/30468k available (1582k kernel code, 320k reserved, 377k data, 112k init, 0k highmem)
totalram_pages= 7537
Calibrating delay loop... 211.35 BogoMIPS (lpj=1056768)
loops_per_jiffy=1056768
Mount-cache hash table entries: 512
Checking for 'wait' instruction...  available.
NET: Registered protocol family 16
Can't analyze prologue code at 9418a174
Squashfs 2.2-r2b (released 2006/02/23) (C) 2002-2005 Phillip Lougher
avm_net_trace: Up and running.
[avm_power]Ohio250 detected -> overclocking possible
[avm] configured: watchdog eventled enable shift register enable direct gpio
        gpio usage: reset=12 clock=13 store=10 data=9
AR7WDT: Watchdog Driver for AR7 Hardware (Version 1.0, build: Jun 25 2009 13:11:54)
Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled
[uart_add_one_port]
ttyS0 at MMIO 0x0 (irq = 15) is a OHIO_UART
[uart_add_one_port] dont register console port->type = 16
port->cons = 0x941c9fe0 port->cons->flags = 0x7
[uart_add_one_port] success
io scheduler noop registered
[cpmac] Version: URL: svn://EmbeddedVM/home/SVN/drivers/cpmac/tags/1.98-r684-trunk-AR8216_MC  -  Revision 538:685  -  Do 25. Jun 13:13:00 CEST 2009
[avm_event_source_trigger]: not registered
[cpmac] [cpmac_if_register] dev cpmac0 (phy_id 0) registered
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
physmap flash device: 400000 at 10000000
phys_mapped_flash: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
phys_mapped_flash: Swapping erase regions for broken CFI table.
number of CFI chips: 1
RedBoot partition parsing not available
Generic platform RAM MTD, (c) 2004 Simtec Electronics
Ohio flash driver (size->0x400000 mem->0x10000000)
flash_size=0x800000
flash_mask=0xffffff
Ohio flash memory: Found 1 x16 devices at 0x0 in 16-bit bank
[genprobe_ident_chips] 4 i 0 j 0
[genprobe_ident_chips] 5 i 0 j 1
 Amd/Fujitsu Extended Query Table at 0x0040
Ohio flash memory: Swapping erase regions for broken CFI table.
number of CFI chips: 1
[mtd]: jffs2_size = 19 * 64KByte (0x130000 Bytes)
[ohio_find_hidden_filesystem]: super block found: bytes_used: 0x594263/5849699
[init_ohio_flash] find hidden filesystem size=0x6c8d00 offset=0xb7300
[mtd] configure jffs2 partition
[mtd] fs_size=0x640000 max=0x130000 is=0x130000 max jffs2_size value 19
[mtd] ohio_flash_map: name=Ohio flash memory bankwidth=2 virt=0xb0000000 phys=0x10000000 size=0x800000
Creating 7 MTD partitions on "Ohio flash memory":
0x000b7300-0x00780000 : "filesystem"
        'nor-flash'
        'Bits can be cleared (flash)'
        'Has an erase function'
mtd: partition "filesystem" doesn't start on an erase block boundary -- force read-only
0x00010000-0x00780000 : "kernel"
        'nor-flash'
        'Bits can be cleared (flash)'
        'Has an erase function'
0x00000000-0x00010000 : "bootloader"
        'nor-flash'
        'Bits can be cleared (flash)'
        'Has an erase function'
0x00780000-0x007c0000 : "tffs (1)"
        'nor-flash'
        'Bits can be cleared (flash)'
        'Has an erase function'
0x007c0000-0x00800000 : "tffs (2)"
        'nor-flash'
        'Bits can be cleared (flash)'
        'Has an erase function'
0x00650000-0x00780000 : "jffs2"
        'nor-flash'
        'Bits can be cleared (flash)'
        'Has an erase function'
0x00010000-0x00650000 : "Kernel without jffs2"
        'nor-flash'
        'Bits can be cleared (flash)'
        'Has an erase function'
partition_info[0]: name=filesystem offset=b7300 size=6c8d00
partition_info[0]: 0xb00b7300: 0x73717368 0x756
partition_info[1]: name=kernel offset=10000 size=770000
partition_info[1]: 0xb0010000: 0xfeed1281 0xa72cc
partition_info[2]: name=bootloader offset=0 size=10000
partition_info[2]: 0xb0000000: 0x40809000 0x40809800
partition_info[3]: name=tffs (1) offset=780000 size=40000
partition_info[3]: 0xb0780000: 0x40001 0xfbffffff
partition_info[4]: name=tffs (2) offset=7c0000 size=40000
partition_info[4]: 0xb07c0000: 0x40001 0xfcffffff
partition_info[5]: name=jffs2 offset=650000 size=130000
partition_info[5]: 0xb0650000: 0x20031985 0xc
partition_info[6]: name=Kernel without jffs2 offset=10000 size=640000
partition_info[6]: 0xb0010000: 0xfeed1281 0xa72cc
NET: Registered protocol family 2
IP route cache hash table entries: 512 (order: -1, 2048 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
TCP bic registered
mcfw: IGMPv3 fast forwarding
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
[setup_irq]: irq 1 irqaction->handler 0x94001590 (dummy_timer_irq+0x0/0x14 )
[setup_irq]: irq 6 irqaction->handler 0x940015a4 (dummy_system_irq_2+0x0/0x14 )
[ohio_late_init]
[avm_new] push_button_gpio=8 value=1 enabled
TFFS: tiny flash file system driver. GPL (c) AVM Berlin (Version 2.0)
      mount on mtd4 and mtd5 (double buffering)
Adam2 environment variables API installed.
[prepare_namespace] new mount root /dev/mtdblock1
use lzma compression
VFS: Mounted root (squashfs filesystem) readonly.
Freeing prom memory: 0kb freed
Freeing unused kernel memory: 112k freed (7565 free)
[setup_irq]: irq 15 irqaction->handler 0x940da99c (serial8250_interrupt+0x0/0x13c )
init started: BusyBox v1.8.2 (2008-09-04 11:11:03 CEST)
starting pid 99, tty '/dev/console': '/etc/init.d/rc.S'
AR7WDT: System Init UEberwachung 240 Sekunden
TFFS Name Table E
HWRevision      127.1.1.0
ProductID       Fritz_Box_7170_AnnexA
SerialNumber    0000000000000000
annex   A
autoload        yes
bootloaderVersion       1.347
bootserport     tty0
country 031
cpufrequency    211968000
firstfreeaddress        0x946C0D14
firmware_version        avme
firmware_info   58.04.68
flashsize       0x00800000
jffs2_size      19
maca    00:1C:4A:26:AE:10
macb    00:1C:4A:26:AE:11
macwlan 00:1C:4A:07:96:72
macdsl  00:1C:4A:26:AE:12
memsize 0x02000000
modetty0        38400,n,8,1,hw
modetty1        38400,n,8,1,hw
mtd0    0x90000000,0x90000000
mtd1    0x90010000,0x90780000
mtd2    0x90000000,0x90010000
mtd3    0x90780000,0x907C0000
mtd4    0x907C0000,0x90800000
my_ipaddress    192.168.178.1
prompt  Eva_AVM
ptest
req_fullrate_freq       125000000
sysfrequency    125000000
tr069_passphrase        XYJkubNKuSsf
tr069_serial    00040E-001C4A26AE10
urlader-version 1347
usb_board_mac   00:1C:4A:26:AE:13
usb_rndis_mac   00:1C:4A:26:AE:14
usb_device_id   0x3D00
usb_revision_id 0x0200
usb_device_name USB DSL Device
usb_manufacturer_name   AVM
wlan_key        7411555752548263
wlan_cal        0006,03F3,0012,00F3,010A,00F6,010A,0352,0349
mknod: /var/flash/ar7.cfg: File exists
Piglet: module license '
(C) Copyright 2005 by AVM
' taints kernel.
EMIF: asize=1 ta=3 r_hold=0 w_strobe=6 r_strobe=6 ew=1
[piglet]McSP: rFS: 8000 Hz rCLK:2048285 Hz
[avm_new]push_button 'Wlan-Taster', released: GPIO=8 presses=5000 key=button_key_2
[jffs2] xx=mtd6: 00130000 00010000 "jffs2"
[jffs2] i=mtd6:
[jffs2] jffs2_pat=6
[jffs2] i=00130000
[jffs2] jffs2_size=19
[jffs2] i=00010000
[jffs2] i="jffs2"
[jffs2] load jffs2 module
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
[jffs2] mount jffs
[jffs2] write env variable jffs2_size to 19
TAM: create JFFS2 directory /data/tam
attempting to load DSL Firmware '/lib/modules/microvoip-dsl.bin'
**** ANNEX: 'A'
*************************************
setting DSL Firmware to Annex A
registered device TI Avalanche SAR
tiatm driver (patch_annex=0xc00e40cc)
[tiatm] Set StrictPriority=0
DSP binary filesize = 389206 bytes
[dsl_ur8] dsl serial number successfully set to "465249545a21426f7820466f6e20574c414e2037093030314334413236414531"
[tiatm] INFO V2U-BRIDGEREGISTER: 0x00000019
[avm_power]Ohio250 detected -> overclocking possible
[avm_power]#### boostVoltage: DSP Core voltage set to 1,5 V ####
[setup_irq]: irq 23 irqaction->handler 0xc00ca208 (tn7atm_sar_irq+0x0/0x30 [tiatm] )
[setup_irq]: irq 31 irqaction->handler 0xc00ca238 (tn7atm_dsl_irq+0x0/0x28 [tiatm] )
[tiatm]: Powermanagment (States => 1,3,10) supported!
[tiatm] AvmInterface length: 44
[avm_power]#### boostVoltage: DSP Core voltage set to 1,65 V ####
Texas Instruments ATM driver: version:[4.08.00.00]
ubik2 driver (ubik2 - 0x10=0xc003efd4)
atm_dsp_register_ubik2: ubik2_ToMIPS_notify=0xc002cbfc
atm_dsp_register_ubik2: dsp mem pointer 0xa1c1644c
ubik2_init_interface: DSP-Link Version v3 8480
[4294938485][isdn]svn:2592
driver params overwritten io_addr=0x0 irq_num=0
[setup_irq]: irq 28 irqaction->handler 0xC0037AF0 (soft_interrupt_handler+0x0/0x30 [ubik2] )
[4294938487]CPU-Clk: 105 * 2 MHz
[4294938661]DSP-Fw: Version 3.390] EC=0 DTMF=0 Slots=10 BChan=8(Analog=4) DChan=2 Fifo=128 Bitfile: EMIF
capicodec_init()
[capi_codec] support fax
[capi_codec] support Codecs
usbcore: registered new driver usbfs
usbcore: registered new driver hub
AHCI RevisionID = 0x02, RamSize = 16384, NumPorts= 1
[setup_irq]: irq 9 irqaction->handler 0xC00BF490 (ahci_irq+0x0/0x880 [usbahcicore] )
ahci : new USB bus registered, assigned bus number 1
AVM USB 1.1 Host started
kdsldmod: init start (Jun 25 2009 15:01:21) sizeof(struct sk_buff)=176
kdsldmod: init done
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
MAC WLAN:       00:1C:4A:07:96:72
WLAN is not enabled
ifconfig: SIOCGIFFLAGS: No such device
ifconfig: SIOCGIFFLAGS: No such device
ifconfig: SIOCGIFFLAGS: No such device
ifconfig: SIOCGIFFLAGS: No such device
ifconfig: SIOCGIFFLAGS: No such device
ifconfig: SIOCGIFFLAGS: No such device
/etc/init.d/rc.net: line 379: websrv: not found
[4294939660]DSP: XDU=0( ) OVR=0 MIPS_OVR=5
[setup_irq]: irq 27 irqaction->handler 0x940EB40C (cpmac_main_isr+0x0/0x78 )
checkempty: : No such file or directory
[cpmac] cpmac_main_ioctl, unknown ioctl 35142
device cpmac0 entered promiscuous mode
device eth0 entered promiscuous mode
lan: port 1(eth0) entering learning state
lan: topology change detected, propagating
lan: port 1(eth0) entering forwarding state
[tiatm]: error getting DSL parametrization interface for read operation!
[avm_power] : ethernet port 0 status 2
[avm_power] : ethernet port 1 status 1
[avm_power] : ethernet port 2 status 1
[avm_power] : ethernet port 3 status 1
Jan  1 01:00:27 telefon[354]: use clock_gettime(CLOCK_MONOTONIC)!
Jan  1 01:00:28 telefon[354]: SIGCHLD received!
Jan  1 01:00:28 telefon[354]: WARNING No config file '/var/flash/fx_def' !
create sema UPNPAPI_DATA_phonebook
/etc/init.d/rc.S: line 1366: /etc/init.d/rc.media: not found
run_clock demon started

AR7WDT: System Init UEberwachung abgeschlossen (212950 ms noch verfuegbar)
[avm_power] pm_ressourceinfo_scriptparse: powerdevice_cpuclock: norm_power_rate=100 act_rate=99 mul=0 div=1 offset=0 NormP=0 mW -> SumNormP=0 mW
[avm_power] pm_ressourceinfo_scriptparse: powerdevice_dspclock: norm_power_rate=100 act_rate=100 mul=154 div=10 offset=974 NormP=2514 mW -> SumNormP=2514 mW
[avm_power] pm_ressourceinfo_scriptparse: powerdevice_systemclock: norm_power_rate=100 act_rate=83 mul=65 div=10 offset=1793 NormP=2443 mW -> SumNormP=4957 mW
[avm_power] pm_ressourceinfo_scriptparse: powerdevice_wlan: norm_power_rate=100 act_rate=0 mul=84 div=10 offset=100 NormP=940 mW -> SumNormP=5897 mW
[avm_power] pm_ressourceinfo_scriptparse: powerdevice_isdnnt: norm_power_rat
Please press Enter to activate this console. [4294940661]DSP: XDU=0( ) OVR=0 MIPS_OVR=2
cat: read error: Broken pipe

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

147

148

149

150

151

152

153

154

155

156

157

158

159

160

161

162

163

164

165

166

167

168

169

170

171

172

173

174

175

176

177

178

179

180

181

182

183

184

185

186

187

188

189

190

191

192

193

194

195

196

197

198

199

200

201

202

203

204

205

206

207

208

209

210

211

212

213

214

215

216

217

218

219

220

221

222

223

224

225

226

227

228

229

230

231

232

233

234

235

236

237

238

239

240

241

242

243

244

245

246

247

248

249

250

251

252

253

254

255

256

257

258

259

260

261

262

263

264

265

266

267

268

269

270

271

272

273

274

275

276

277

278

279

280

281

282

283

284

285

286

287

288

289

290

291

292

293

294

295

296

297

298

299

300

301

302

303

304

305

306

307

308

309

310

311

312

313

314

(AVM) EVA Revision: 1.347 Version: 1347

[FLASH:] SPANSION Top-MirrorBit-Flash 8MB 32 Bytes WriteBuffer

[FLASH:](Eraseregion [0] 127 sectors a 64kB)

[FLASH:](Eraseregion [1] 8 sectors a 8kB)

[SYSTEM:] OHIO on 211MHz/125MHz

Eva_AVM >AVM decompress Kernel:

..................executeProgram on 0x941EB000

[ohio_pre_init] System Clk = 62500000 Hz

LINUX started...

Linux version 2.6.13.1-ohio (1699) (gcc-Version 3.4.6) #1 Thu Jun 25 13:14:17 CEST 2009

memsize=32 MByte

flashsize=8 MByte

&_end=0x9423ee74 PFN_ALIGN(&_end)=0x9423f000 CPHYSADDR(PFN_ALIGN(&_end))=0x1423f000 memsize=0x2000000

CPU revision is: 00018448

[ohio_gpio_init]

Determined physical RAM map:

memory: 0023f000 @ 14000000 (reserved)

memory: 01dc1000 @ 1423f000 (usable)

On node 0 totalpages: 8192

[alloc_node_mem_map] reduce size from 2883616 Bytes to 262176 Bytes

[alloc_node_mem_map]: (org) sizeof(mem_map) = 262176 mem_map=0x94242000-0x94282020

[alloc_node_mem_map]: sizeof(mem_map) = 2883616 mem_map=0x93fc2000-0x94282020

zone=0 zone_size[j]=0x90112

realsize=8192

DMA zone: 8192 pages, LIFO batch:3

zone=1 zone_size[j]=0x0

realsize=0

Normal zone: 0 pages, LIFO batch:1

zone=2 zone_size[j]=0x0

realsize=0

HighMem zone: 0 pages, LIFO batch:1

Built 1 zonelists

Kernel command line: console=ttyS0,38400n8r

[ld_mmu_r4xx0] memcpy((void *)(CAC_BASE + 0x100), &except_vec2_generic, 0x30)

Primary instruction cache 16kB, physically tagged, 4-way, linesize 16 bytes.

Primary data cache 8kB, 4-way, linesize 16 bytes.

Synthesized TLB refill handler (20 instructions). Base=0x9420578c

TLB synthesizer field overflow (simm)

Synthesized TLB load handler fastpath (34 instructions) Base=0x94208620.

TLB synthesizer field overflow (simm)

Synthesized TLB store handler fastpath (34 instructions) Base=0x94208820.

TLB synthesizer field overflow (simm)

Synthesized TLB modify handler fastpath (33 instructions) Base=0x94208a20.

PID hash table entries: 256 (order: 8, 4096 bytes)

CPU frequency 211.97 MHz

Using 105.984 MHz high precision timer.

[setup_irq]: irq 255 irqaction->handler 0x940430c0 (no_action+0x0/0x8 )

[register_console] enable commandline console 0

Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

Memory: 30092k/30468k available (1582k kernel code, 320k reserved, 377k data, 112k init, 0k highmem)

totalram_pages= 7537

Calibrating delay loop... 211.35 BogoMIPS (lpj=1056768)

loops_per_jiffy=1056768

Mount-cache hash table entries: 512

Checking for 'wait' instruction... available.

NET: Registered protocol family 16

Can't analyze prologue code at 9418a174

avm_net_trace: Up and running.

[avm_power]Ohio250 detected -> overclocking possible

[avm] configured: watchdog eventled enable shift register enable direct gpio

gpio usage: reset=12 clock=13 store=10 data=9

AR7WDT: Watchdog Driver for AR7 Hardware (Version 1.0, build: Jun 25 2009 13:11:54)

Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled

[uart_add_one_port]

ttyS0 at MMIO 0x0 (irq = 15) is a OHIO_UART

[uart_add_one_port] dont register console port->type = 16

port->cons = 0x941c9fe0 port->cons->flags = 0x7

[uart_add_one_port] success

io scheduler noop registered

[cpmac] Version: URL: svn://EmbeddedVM/home/SVN/drivers/cpmac/tags/1.98-r684-trunk-AR8216_MC - Revision 538:685 - Do 25. Jun 13:13:00 CEST 2009

[avm_event_source_trigger]: not registered

[cpmac] [cpmac_if_register] dev cpmac0 (phy_id 0) registered

tun: Universal TUN/TAP device driver, 1.6

physmap flash device: 400000 at 10000000

phys_mapped_flash: Found 1 x16 devices at 0x0 in 16-bit bank

Amd/Fujitsu Extended Query Table at 0x0040

phys_mapped_flash: Swapping erase regions for broken CFI table.

number of CFI chips: 1

RedBoot partition parsing not available

Ohio flash driver (size->0x400000 mem->0x10000000)

flash_size=0x800000

flash_mask=0xffffff

Ohio flash memory: Found 1 x16 devices at 0x0 in 16-bit bank

[genprobe_ident_chips] 4 i 0 j 0

[genprobe_ident_chips] 5 i 0 j 1

Amd/Fujitsu Extended Query Table at 0x0040

Ohio flash memory: Swapping erase regions for broken CFI table.

number of CFI chips: 1

[mtd]: jffs2_size = 19 * 64KByte (0x130000 Bytes)

[ohio_find_hidden_filesystem]: super block found: bytes_used: 0x594263/5849699

[init_ohio_flash] find hidden filesystem size=0x6c8d00 offset=0xb7300

[mtd] configure jffs2 partition

[mtd] fs_size=0x640000 max=0x130000 is=0x130000 max jffs2_size value 19

[mtd] ohio_flash_map: name=Ohio flash memory bankwidth=2 virt=0xb0000000 phys=0x10000000 size=0x800000

Creating 7 MTD partitions on "Ohio flash memory":

0x000b7300-0x00780000 : "filesystem"

'nor-flash'

'Bits can be cleared (flash)'

'Has an erase function'

mtd: partition "filesystem" doesn't start on an erase block boundary -- force read-only

0x00010000-0x00780000 : "kernel"

'nor-flash'

'Bits can be cleared (flash)'

'Has an erase function'

0x00000000-0x00010000 : "bootloader"

'nor-flash'

'Bits can be cleared (flash)'

'Has an erase function'

0x00780000-0x007c0000 : "tffs (1)"

'nor-flash'

'Bits can be cleared (flash)'

'Has an erase function'

0x007c0000-0x00800000 : "tffs (2)"

'nor-flash'

'Bits can be cleared (flash)'

'Has an erase function'

0x00650000-0x00780000 : "jffs2"

'nor-flash'

'Bits can be cleared (flash)'

'Has an erase function'

0x00010000-0x00650000 : "Kernel without jffs2"

'nor-flash'

'Bits can be cleared (flash)'

'Has an erase function'

partition_info[0]: name=filesystem offset=b7300 size=6c8d00

partition_info[0]: 0xb00b7300: 0x73717368 0x756

partition_info[1]: name=kernel offset=10000 size=770000

partition_info[1]: 0xb0010000: 0xfeed1281 0xa72cc

partition_info[2]: name=bootloader offset=0 size=10000

partition_info[2]: 0xb0000000: 0x40809000 0x40809800

partition_info[3]: name=tffs (1) offset=780000 size=40000

partition_info[3]: 0xb0780000: 0x40001 0xfbffffff

partition_info[4]: name=tffs (2) offset=7c0000 size=40000

partition_info[4]: 0xb07c0000: 0x40001 0xfcffffff

partition_info[5]: name=jffs2 offset=650000 size=130000

partition_info[5]: 0xb0650000: 0x20031985 0xc

partition_info[6]: name=Kernel without jffs2 offset=10000 size=640000

partition_info[6]: 0xb0010000: 0xfeed1281 0xa72cc

NET: Registered protocol family 2

IP route cache hash table entries: 512 (order: -1, 2048 bytes)

TCP established hash table entries: 2048 (order: 2, 16384 bytes)

TCP bind hash table entries: 2048 (order: 1, 8192 bytes)

TCP: Hash tables configured (established 2048 bind 2048)

TCP reno registered

TCP bic registered

mcfw: IGMPv3 fast forwarding

NET: Registered protocol family 1

NET: Registered protocol family 17

NET: Registered protocol family 8

NET: Registered protocol family 20

[setup_irq]: irq 1 irqaction->handler 0x94001590 (dummy_timer_irq+0x0/0x14 )

[setup_irq]: irq 6 irqaction->handler 0x940015a4 (dummy_system_irq_2+0x0/0x14 )

[ohio_late_init]

[avm_new] push_button_gpio=8 value=1 enabled

TFFS: tiny flash file system driver. GPL (c) AVM Berlin (Version 2.0)

mount on mtd4 and mtd5 (double buffering)

Adam2 environment variables API installed.

[prepare_namespace] new mount root /dev/mtdblock1

use lzma compression

VFS: Mounted root (squashfs filesystem) readonly.

Freeing prom memory: 0kb freed

Freeing unused kernel memory: 112k freed (7565 free)

[setup_irq]: irq 15 irqaction->handler 0x940da99c (serial8250_interrupt+0x0/0x13c )

init started: BusyBox v1.8.2 (2008-09-04 11:11:03 CEST)

starting pid 99, tty '/dev/console': '/etc/init.d/rc.S'

AR7WDT: System Init UEberwachung 240 Sekunden

TFFS Name Table E

HWRevision 127.1.1.0

ProductID Fritz_Box_7170_AnnexA

SerialNumber 0000000000000000

annex A

autoload yes

bootloaderVersion 1.347

bootserport tty0

country 031

cpufrequency 211968000

firstfreeaddress 0x946C0D14

firmware_version avme

firmware_info 58.04.68

flashsize 0x00800000

jffs2_size 19

maca 00:1C:4A:26:AE:10

macb 00:1C:4A:26:AE:11

macwlan 00:1C:4A:07:96:72

macdsl 00:1C:4A:26:AE:12

memsize 0x02000000

modetty0 38400,n,8,1,hw

modetty1 38400,n,8,1,hw

mtd0 0x90000000,0x90000000

mtd1 0x90010000,0x90780000

mtd2 0x90000000,0x90010000

mtd3 0x90780000,0x907C0000

mtd4 0x907C0000,0x90800000

my_ipaddress 192.168.178.1

prompt Eva_AVM

ptest

req_fullrate_freq 125000000

sysfrequency 125000000

tr069_passphrase XYJkubNKuSsf

tr069_serial 00040E-001C4A26AE10

urlader-version 1347

usb_board_mac 00:1C:4A:26:AE:13

usb_rndis_mac 00:1C:4A:26:AE:14

usb_device_id 0x3D00

usb_revision_id 0x0200

usb_device_name USB DSL Device

usb_manufacturer_name AVM

wlan_key 7411555752548263

wlan_cal 0006,03F3,0012,00F3,010A,00F6,010A,0352,0349

mknod: /var/flash/ar7.cfg: File exists

Piglet: module license '

' taints kernel.

EMIF: asize=1 ta=3 r_hold=0 w_strobe=6 r_strobe=6 ew=1

[piglet]McSP: rFS: 8000 Hz rCLK:2048285 Hz

[avm_new]push_button 'Wlan-Taster', released: GPIO=8 presses=5000 key=button_key_2

[jffs2] xx=mtd6: 00130000 00010000 "jffs2"

[jffs2] i=mtd6:

[jffs2] jffs2_pat=6

[jffs2] i=00130000

[jffs2] jffs2_size=19

[jffs2] i=00010000

[jffs2] i="jffs2"

[jffs2] load jffs2 module

[jffs2] mount jffs

[jffs2] write env variable jffs2_size to 19

TAM: create JFFS2 directory /data/tam

attempting to load DSL Firmware '/lib/modules/microvoip-dsl.bin'

**** ANNEX: 'A'

*************************************

setting DSL Firmware to Annex A

registered device TI Avalanche SAR

tiatm driver (patch_annex=0xc00e40cc)

[tiatm] Set StrictPriority=0

DSP binary filesize = 389206 bytes

[dsl_ur8] dsl serial number successfully set to "465249545a21426f7820466f6e20574c414e2037093030314334413236414531"

[tiatm] INFO V2U-BRIDGEREGISTER: 0x00000019

[avm_power]Ohio250 detected -> overclocking possible

[avm_power]#### boostVoltage: DSP Core voltage set to 1,5 V ####

[setup_irq]: irq 23 irqaction->handler 0xc00ca208 (tn7atm_sar_irq+0x0/0x30 [tiatm] )

[setup_irq]: irq 31 irqaction->handler 0xc00ca238 (tn7atm_dsl_irq+0x0/0x28 [tiatm] )

[tiatm]: Powermanagment (States => 1,3,10) supported!

[tiatm] AvmInterface length: 44

[avm_power]#### boostVoltage: DSP Core voltage set to 1,65 V ####

Texas Instruments ATM driver: version:[4.08.00.00]

ubik2 driver (ubik2 - 0x10=0xc003efd4)

atm_dsp_register_ubik2: ubik2_ToMIPS_notify=0xc002cbfc

atm_dsp_register_ubik2: dsp mem pointer 0xa1c1644c

ubik2_init_interface: DSP-Link Version v3 8480

[4294938485][isdn]svn:2592

driver params overwritten io_addr=0x0 irq_num=0

[setup_irq]: irq 28 irqaction->handler 0xC0037AF0 (soft_interrupt_handler+0x0/0x30 [ubik2] )

[4294938487]CPU-Clk: 105 * 2 MHz

[4294938661]DSP-Fw: Version 3.390] EC=0 DTMF=0 Slots=10 BChan=8(Analog=4) DChan=2 Fifo=128 Bitfile: EMIF

capicodec_init()

[capi_codec] support fax

[capi_codec] support Codecs

usbcore: registered new driver usbfs

usbcore: registered new driver hub

AHCI RevisionID = 0x02, RamSize = 16384, NumPorts= 1

[setup_irq]: irq 9 irqaction->handler 0xC00BF490 (ahci_irq+0x0/0x880 [usbahcicore] )

ahci : new USB bus registered, assigned bus number 1

AVM USB 1.1 Host started

kdsldmod: init start (Jun 25 2009 15:01:21) sizeof(struct sk_buff)=176

kdsldmod: init done

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 1 port detected

MAC WLAN: 00:1C:4A:07:96:72

WLAN is not enabled

ifconfig: SIOCGIFFLAGS: No such device

/etc/init.d/rc.net: line 379: websrv: not found

[4294939660]DSP: XDU=0( ) OVR=0 MIPS_OVR=5

[setup_irq]: irq 27 irqaction->handler 0x940EB40C (cpmac_main_isr+0x0/0x78 )

checkempty: : No such file or directory

[cpmac] cpmac_main_ioctl, unknown ioctl 35142

device cpmac0 entered promiscuous mode

device eth0 entered promiscuous mode

lan: port 1(eth0) entering learning state

lan: topology change detected, propagating

lan: port 1(eth0) entering forwarding state

[tiatm]: error getting DSL parametrization interface for read operation!

[avm_power] : ethernet port 0 status 2

[avm_power] : ethernet port 1 status 1

[avm_power] : ethernet port 2 status 1

[avm_power] : ethernet port 3 status 1

Jan 1 01:00:27 telefon[354]: use clock_gettime(CLOCK_MONOTONIC)!

Jan 1 01:00:28 telefon[354]: SIGCHLD received!

Jan 1 01:00:28 telefon[354]: WARNING No config file '/var/flash/fx_def' !

create sema UPNPAPI_DATA_phonebook

/etc/init.d/rc.S: line 1366: /etc/init.d/rc.media: not found

run_clock demon started

AR7WDT: System Init UEberwachung abgeschlossen (212950 ms noch verfuegbar)

[avm_power] pm_ressourceinfo_scriptparse: powerdevice_cpuclock: norm_power_rate=100 act_rate=99 mul=0 div=1 offset=0 NormP=0 mW -> SumNormP=0 mW

[avm_power] pm_ressourceinfo_scriptparse: powerdevice_dspclock: norm_power_rate=100 act_rate=100 mul=154 div=10 offset=974 NormP=2514 mW -> SumNormP=2514 mW

[avm_power] pm_ressourceinfo_scriptparse: powerdevice_systemclock: norm_power_rate=100 act_rate=83 mul=65 div=10 offset=1793 NormP=2443 mW -> SumNormP=4957 mW

[avm_power] pm_ressourceinfo_scriptparse: powerdevice_wlan: norm_power_rate=100 act_rate=0 mul=84 div=10 offset=100 NormP=940 mW -> SumNormP=5897 mW

[avm_power] pm_ressourceinfo_scriptparse: powerdevice_isdnnt: norm_power_rat

Please press Enter to activate this console. [4294940661]DSP: XDU=0( ) OVR=0 MIPS_OVR=2

cat: read error: Broken pipe

Zoeken

Tag: UART

Samsung SMT-6010E – Boot LOG (UART)

KPN Experia Box (Arcadyan ARV7519) – UART aansluiting

KPN Experia Box (Arcadyan ARV7519) – Bootlog via UART

PL2303 USB to UART Bridge Drivers (Windows)

Plugwise Stretch 2.0 – Firmware uploaden (bootloader)

Plugwise Smile P1 – Firmware uploaden (bootloader)

Fritz!Box Fon WLAN 7170 – Firmware I/O via bootloader

Fritz!Box Fon WLAN 7170 – Firmware I/O via telnet

Fritz!Box Fon WLAN 7170 – UART / JTAG aansluiting

Fritz!Box Fon WLAN 7170 – Bootlog via UART