Bootlog Archieven - DomoticX Knowledge Center

Linksys SRW2008x (managed switch) – Webinterface

Door Sebastiaan Geplaatst op 2016-06-04 Geplaatst in Linksys Tagged with 192.168.1.254, Bootlog, Hardware info, Linksys, Managed switch, SRW2008x, switch, Webinterface

Linksys SRW2008x (managed switch) Let op: De javascripts van de webinterface van deze switch bevat voor de modernere browsers “fouten” …

Linksys SRW2008x (managed switch) – Webinterface Lees meer »

Linksys SRW2008x (managed switch) – Bootlog

Door Sebastiaan Geplaatst op 2016-06-04 Geplaatst in Linksys Tagged with Bootlog, Firmware, Hardware info, Linksys, Managed switch, SRW2008x, switch

Linksys SRW2008x (managed switch) Bootlog

------ Performing the Power-On Self Test (POST) ------

UART Channel Loopback Test........................PASS

Testing the System SDRAM..........................PASS

Boot1 Checksum Test...............................PASS

Boot2 Checksum Test...............................PASS

Flash Image Validation Test.......................PASS



BOOT Software Version 1.0.1 Built  06-Jun-2006  17:23:21

:::
:::        ::: :::       ::: :::     :::::  :::::::::: :::      ::: ::::::::::
:::        ::: :::::     ::: :::   :::::   ::::     ::: ::::  :::: ::::     :::
:::        ::: ::: :::   ::: ::::::::      ::::          ::::::::  ::::
:::        ::: :::   ::  ::: ::::::::::     ::::::::::     ::::     ::::::::::
:::        ::: :::    :::::: :::    ::::            :::    ::::             :::
:::::::::: ::: :::      :::: :::      :::: :::......:::    ::::    :::......:::
 ......... ... ...       ... ...       .... ..........     ....     ..........

Linksys SmartSwitch SRW208 based on 88E6218 with ARM946E-S.
32MByte SDRAM. I-Cache 8 KB. D-Cache 8 KB. Cache Enabled.

Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.
Preparing to decompress...
 100%
Decompressing SW from flash
 100%

OK
Running from RAM...

******************************************************************
*** Running  SW  Ver. 1.0.4  Date  06-Sep-2007  Time  09:11:40 ***
******************************************************************

HW version is 00.03.00
Base Mac address is: 00:22:6b:c0:79:d1
Dram size is  : 32M bytes
Dram first block size is  : 17152K bytes
Dram first PTR is  : 0xF40000
Flash size is: 8M
01-Jan-2000 01:01:05 %CDB-I-LOADCONFIG: Loading startup configuration.
Device configuration:
PCB revision: 1
Slot 1 - SRW2008MP HW Rev.  0.1
Tapi Version: v1.3.3.1
Core Version: v1.3.3.1
01-Jan-2000 01:01:19 %INIT-I-InitCompleted: Initialization task is completed


                          Login Screen
                          ============


                       User Name:

                       Password:

------ Performing the Power-On Self Test (POST) ------

UART Channel Loopback Test........................PASS

Testing the System SDRAM..........................PASS

Boot1 Checksum Test...............................PASS

Boot2 Checksum Test...............................PASS

Flash Image Validation Test.......................PASS

BOOT Software Version 1.0.1 Built 06-Jun-2006 17:23:21

:::

::: ::: ::: ::: ::: ::::: :::::::::: ::: ::: ::::::::::

::: ::: ::::: ::: ::: ::::: :::: ::: :::: :::: :::: :::

::: ::: ::: ::: ::: :::::::: :::: :::::::: ::::

::: ::: ::: :: ::: :::::::::: :::::::::: :::: ::::::::::

::: ::: ::: :::::: ::: :::: ::: :::: :::

:::::::::: ::: ::: :::: ::: :::: :::......::: :::: :::......:::

......... ... ... ... ... .... .......... .... ..........

Linksys SmartSwitch SRW208 based on 88E6218 with ARM946E-S.

32MByte SDRAM. I-Cache 8 KB. D-Cache 8 KB. Cache Enabled.

Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.

Preparing to decompress...

100%

Decompressing SW from flash

100%

Running from RAM...

******************************************************************

*** Running SW Ver. 1.0.4 Date 06-Sep-2007 Time 09:11:40 ***

******************************************************************

HW version is 00.03.00

Base Mac address is: 00:22:6b:c0:79:d1

Dram size is : 32M bytes

Dram first block size is : 17152K bytes

Dram first PTR is : 0xF40000

Flash size is: 8M

01-Jan-2000 01:01:05 %CDB-I-LOADCONFIG: Loading startup configuration.

Device configuration:

PCB revision: 1

Slot 1 - SRW2008MP HW Rev. 0.1

Tapi Version: v1.3.3.1

Core Version: v1.3.3.1

01-Jan-2000 01:01:19 %INIT-I-InitCompleted: Initialization task is completed

============

User Name:

Password:

Hardware info

                                Versions
                                ========

  Boot Version:          1.0.1 (Date:  06-Jun-2006, Time:  17:23:21)

  Software Version:      1.0.4 (Date:  06-Sep-2007, Time:  09:11:40)

  Hardware Version:      00.03.00


                          General System Information
                          ==========================

  System Description:    SRW2008MP - 6-port Gigabit Switch with 2 Combo ports,

  System Up Time:        0,00:05:20 (days,hour:min:sec)

  System MAC Address:    00:22:6b:c0:79:d1

  System Contact:

  System Name:

  System Location:

Versions

========

Boot Version: 1.0.1 (Date: 06-Jun-2006, Time: 17:23:21)

Software Version: 1.0.4 (Date: 06-Sep-2007, Time: 09:11:40)

Hardware Version: 00.03.00

General System Information

==========================

System Description: SRW2008MP - 6-port Gigabit Switch with 2 Combo ports,

System Up Time: 0,00:05:20 (days,hour:min:sec)

System MAC Address: 00:22:6b:c0:79:d1

System Contact:

System Name:

System Location:

Linksys WAG354G (ADSL router) – Bootlog via UART

Door Sebastiaan Geplaatst op 2016-04-08 Geplaatst in Linksys Tagged with ADSL, Bootlog, Firmware, Linksys, Router, UART, WAG354G, WLAN

Linksys WAG354G v1/v2 (ADSL router) Bootlog via UART Dit is de OEM bootlog bij het opstarten via de UART seriele …

Linksys WAG354G (ADSL router) – Bootlog via UART Lees meer »

Samsung SMT-6010E – Firmware

Door Sebastiaan Geplaatst op 2016-02-21 Geplaatst in Samsung Tagged with Bootlog, Box, decoder, Linux, Samsung, SMT-6010E, SMT-6010E_OpenSource, UART

Het firmware bestand “SMT-6010E_OpenSource.zip” voor deze decoder is te vinden op samsung.com.

Samsung SMT-6010E – Linux gegevens

Door Sebastiaan Geplaatst op 2016-02-21 Geplaatst in Samsung Tagged with Bootlog, Box, decoder, Linux, Samsung, SMT-6010E, UART

Linux gegevens:

Linux version 2.2.20 (root@MF-DEV-SSBUILD01) (ecc version v6.0_6127) #1 Wed Dec 15 13:10:43 CET 2010

1	Linux version 2.2.20 (root@MF-DEV-SSBUILD01) (ecc version v6.0_6127) #1 Wed Dec 15 13:10:43 CET 2010

CPU             : BSP 1.0 (0x20000)
cpu MHz         : 297.000
mem MHz         : 118.800000
BogoMIPS        : 296.55

CPU : BSP 1.0 (0x20000)

cpu MHz : 297.000

mem MHz : 118.800000

BogoMIPS : 296.55

02f8-02ff : serial(auto)
03f8-03ff : serial(auto)
1000-10ff : eth0
1120-1133 : usb-uhci

02f8-02ff : serial(auto)

03f8-03ff : serial(auto)

1000-10ff : eth0

1120-1133 : usb-uhci

total:    used:    free:  shared: buffers:  cached:
Mem:  126877696 124436480  2441216  6324224 30425088 22233088
Swap:        0        0        0
MemTotal:    123904 kB
MemFree:       2384 kB
MemShared:     6176 kB
Buffers:      29712 kB
Cached:       21712 kB
SwapTotal:        0 kB
SwapFree:         0 kB

total: used: free: shared: buffers: cached:

Mem: 126877696 124436480 2441216 6324224 30425088 22233088

Swap: 0 0 0

MemTotal: 123904 kB

MemFree: 2384 kB

MemShared: 6176 kB

Buffers: 29712 kB

Cached: 21712 kB

SwapTotal: 0 kB

SwapFree: 0 kB

major minor  #blocks  name
 
  62     0      16544 fla
  62     1      16531 fla1

major minor #blocks name

62 0 16544 fla

62 1 16531 fla1

IrDrv                  29904   1
cs4341Control          23832   1
DmaBufferDrv           16944   1
DrcDrv                 96936   1
AoutDrv                63844   1
ScrDrv                 35992   1
mediaDev              691444   1 [IrDrv DrcDrv AoutDrv ScrDrv]
streaming             126764   0 [DrcDrv AoutDrv mediaDev]
dmaBuffers             17280   0 [DmaBufferDrv streaming]
boardSupportDev       321484   1 [mediaDev]
noncoregpDev           76704   0 [mediaDev boardSupportDev]
PageClusterDrv         19048   1
EventDrv               15112   1
ProcessInfoDrv         13372   1
processInfo             5116   0 [IrDrv cs4341Control DmaBufferDrv DrcDrv AoutDrv ScrDrv streaming PageClusterDrv EventDrv ProcessInfoDrv]
KernelEvents            4016   0 [DrcDrv streaming EventDrv processInfo]
pageCluster             5032   0 [PageClusterDrv]
cxa2161r                8232   1
saa7128                 6632   1
8139too                58192   1
doc                   708936   1

IrDrv 29904 1

cs4341Control 23832 1

DmaBufferDrv 16944 1

DrcDrv 96936 1

AoutDrv 63844 1

ScrDrv 35992 1

mediaDev 691444 1 [IrDrv DrcDrv AoutDrv ScrDrv]

streaming 126764 0 [DrcDrv AoutDrv mediaDev]

dmaBuffers 17280 0 [DmaBufferDrv streaming]

boardSupportDev 321484 1 [mediaDev]

noncoregpDev 76704 0 [mediaDev boardSupportDev]

PageClusterDrv 19048 1

EventDrv 15112 1

ProcessInfoDrv 13372 1

processInfo 5116 0 [IrDrv cs4341Control DmaBufferDrv DrcDrv AoutDrv ScrDrv streaming PageClusterDrv EventDrv ProcessInfoDrv]

KernelEvents 4016 0 [DrcDrv streaming EventDrv processInfo]

pageCluster 5032 0 [PageClusterDrv]

cxa2161r 8232 1

saa7128 6632 1

8139too 58192 1

doc 708936 1

Character devices:
  1 mem
  2 pty
  3 ttyp
  4 ttyS
  5 cua
 10 misc
 13 input
100 bootDriver
128 ptm
136 pts
180 usb
252 Cxa2161rScart
254 Saa7128color
 
Block devices:
  1 ramdisk
 62 fl

Character devices:

1 mem

2 pty

3 ttyp

4 ttyS

5 cua

10 misc

13 input

100 bootDriver

128 ptm

136 pts

180 usb

252 Cxa2161rScart

254 Saa7128color

Block devices:

1 ramdisk

62 fl

[root:/etc]# cat /etc/passwd
root:$1$$ssYAig.f1ZwT0N5M3yCFR.:0:0:root:/:/bin/sh
bin:x:1:1:bin:/bin:
daemon:x:2:2:daemon:/sbin:
nobody:x:99:99:Nobody:/:
ftp:x:14:100:FTP User:/:
eti::100:100:ETI User:/tmp:/bin/sh
VSstblogin01:$1$$j2o6P3pu8c2A5dhDlm3QK/:0:0:Linux User,,,:/:/bin/sh

[root:/etc]# cat /etc/passwd

root:$1$$ssYAig.f1ZwT0N5M3yCFR.:0:0:root:/:/bin/sh

bin:x:1:1:bin:/bin:

daemon:x:2:2:daemon:/sbin:

nobody:x:99:99:Nobody:/:

ftp:x:14:100:FTP User:/:

eti::100:100:ETI User:/tmp:/bin/sh

VSstblogin01:$1$$j2o6P3pu8c2A5dhDlm3QK/:0:0:Linux User,,,:/:/bin/sh

root:$1$$OEJ8lYz3qOTTGcQaMyjQj.:0:0:root:/:/bin/sh
bin:x:1:1:bin:/bin:
daemon:x:2:2:daemon:/sbin:
nobody:x:99:99:Nobody:/:
ftp:x:14:100:FTP User:/:
eti::100:100:ETI User:/tmp:/bin/sh
G9v3p3jmanXS:$1$$HVO2F/9PcBplVntUhlRKt.:0:0:Linux User,,,:/bin/sh

root:$1$$OEJ8lYz3qOTTGcQaMyjQj.:0:0:root:/:/bin/sh

bin:x:1:1:bin:/bin:

daemon:x:2:2:daemon:/sbin:

nobody:x:99:99:Nobody:/:

ftp:x:14:100:FTP User:/:

eti::100:100:ETI User:/tmp:/bin/sh

G9v3p3jmanXS:$1$$HVO2F/9PcBplVntUhlRKt.:0:0:Linux User,,,:/bin/sh

hub.c: USB new device connect on bus1/1, assigned device number 2
usb.c: USB new device connect, assigned device number 2
Manufacturer: USB
Product: Flash Disk
SerialNumber: AA04012707872
usb.c: USB device 2 (vend/prod 0x90c/0x1000) is not claimed by any active driver.
  Length              = 18
  DescriptorType      = 01
  USB version         = 2.00
  Vendor:Product      = 090c:1000
  MaxPacketSize0      = 64
  NumConfigurations   = 1
  Device version      = 30.00
  Device Class:SubClass:Protocol = 00:00:00
    Per-interface classes
Configuration:
  bLength             =    9
  bDescriptorType     =   02
  wTotalLength        = 0020
  bNumInterfaces      =   01
  bConfigurationValue =   01
  iConfiguration      =   00
  bmAttributes        =   80
  MaxPower            =  100mA
 
  Interface: 0
  Alternate Setting:  0
    bLength             =    9
    bDescriptorType     =   04
    bInterfaceNumber    =   00
    bAlternateSetting   =   00
    bNumEndpoints       =   02
    bInterface Class:SubClass:Protocol =   08:06:50
    iInterface          =   00
    Endpoint:
      bLength             =    7
      bDescriptorType     =   05
      bEndpointAddress    =   81 (in)
      bmAttributes        =   02 (Bulk)
      wMaxPacketSize      = 0040
      bInterval           =   ff
    Endpoint:
      bLength             =    7
      bDescriptorType     =   05
      bEndpointAddress    =   02 (out)
      bmAttributes        =   02 (Bulk)
      wMaxPacketSize      = 0040
      bInterval           =   ff

hub.c: USB new device connect on bus1/1, assigned device number 2

usb.c: USB new device connect, assigned device number 2

Manufacturer: USB

Product: Flash Disk

SerialNumber: AA04012707872

usb.c: USB device 2 (vend/prod 0x90c/0x1000) is not claimed by any active driver.

Length = 18

DescriptorType = 01

USB version = 2.00

Vendor:Product = 090c:1000

MaxPacketSize0 = 64

NumConfigurations = 1

Device version = 30.00

Device Class:SubClass:Protocol = 00:00:00

Per-interface classes

Configuration:

bLength = 9

bDescriptorType = 02

wTotalLength = 0020

bNumInterfaces = 01

bConfigurationValue = 01

iConfiguration = 00

bmAttributes = 80

MaxPower = 100mA

Interface: 0

Alternate Setting: 0

bLength = 9

bDescriptorType = 04

bInterfaceNumber = 00

bAlternateSetting = 00

bNumEndpoints = 02

bInterface Class:SubClass:Protocol = 08:06:50

iInterface = 00

Endpoint:

bLength = 7

bDescriptorType = 05

bEndpointAddress = 81 (in)

bmAttributes = 02 (Bulk)

wMaxPacketSize = 0040

bInterval = ff

Endpoint:

bLength = 7

bDescriptorType = 05

bEndpointAddress = 02 (out)

bmAttributes = 02 (Bulk)

wMaxPacketSize = 0040

bInterval = ff

Samsung SMT-6010E – Aansluiten via UART

Door Sebastiaan Geplaatst op 2016-02-21 Geplaatst in Samsung Tagged with Bootlog, Box, decoder, Samsung, SMT-6010E, UART

De UART aansluiting is de connectie op J7:

+------+ TX 
| heat | RX 
| sink | GND 
+------+ VCC(3.3v)

+------+ TX

| heat | RX

| sink | GND

+------+ VCC(3.3v)

De UART Baudrate is 115200 Root inloggegevens zijn: username: root password: …

Samsung SMT-6010E – Aansluiten via UART Lees meer »

Samsung SMT-6010E – Boot LOG (UART)

Door Sebastiaan Geplaatst op 2016-02-21 Geplaatst in Samsung Tagged with Bootlog, Box, decoder, Samsung, SMT-6010E, UART

BOOT LOG (UART):

Success1 registering the  Video DAC devices for board: 1300, daughter board: 0
Success2 registering the  Video DAC devices for board: 1300, daughter board: 0
Success3 registering the  Video DAC devices for board: 1300, daughter board: 0
[cyg_net_init] Init: mbinit(0x00000000)
[cyg_net_init] Init: cyg_net_init_devs(0x00000000)
Init device 'rltk8139_eth0'
[cyg_net_init] Init: loopattach(0x00000000)
[cyg_net_init] Init: ifinit(0x00000000)
[cyg_net_init] Init: domaininit(0x00000000)
[cyg_net_init] Init: cyg_net_add_domain(0x803afae0)
New domain internet at 0x00000000
[cyg_net_init] Init: cyg_net_add_domain(0x803aea60)
New domain route at 0x00000000
[cyg_net_init] Init: call_route_init(0x00000000)
[cyg_net_init] Done
*************************
* Bootrom Version       *
* V_STB_BT_01_02_050418 *
*************************
pciVIAInit
imageDisplay
Display Refresh Video Output example.
etiDefaultMemPool 0x87efc000 , start 0x80000000 size 0x8000000 hiMemGap 0x104000
xOffset 80 yOffset 48 dstBytesPerPixel 2 imageBmpWidth 640
CXA2161R status : d8
CXA2161R status : d8
Press <CANCEL> remote key to start net booting....
hmpv_read_fcnt
start time in 23eab437 cycles
Doc Booting....
flRegisterSAFTL: start
flRegisterSAFTL: end
Media Size = 32 Mbytes
 
Note: Searching for the media header.
      As a result a few H/W protection error messages might be reported.
 
ERROR in read_Seq: M512_checkAndFixAccessError:Protection error occurred.
ERROR in read_Seq: M512_checkAndFixAccessError:Protection error occurred.
ERROR in read_Seq: M512_checkAndFixAccessError:Protection error occurred.
ERROR in read_Seq: M512_checkAndFixAccessError:Protection error occurred.
 
Note: header was found - end of media header search.
 
DALN: PC=0x8009938c, RP=0x800ff560, addr=0x80a19f39: 2 byte load r60
START WITH BANK0
imageversion : 0
START TIME : 26940493
bdkReadBlock has Completed Succefully
CheckSignature returned 0, nds signature passed
END TIME : b156d10e
Read done in 8d7d1a30 cycles
Start Booting.... address from [82217820]
00:0a:0 Class 0200: 10ec:8139 0:0x1000[256]I 1:0x10000000[256]M IRQ 9
00:0c:0 Class 0601: 1106:0686
00:0c:1 Class 0101: 1106:0571 4:0x1100[16]I
00:0c:2 Class 0c03: 1106:3038 4:0x1120[32]I IRQ 16
00:0c:4 Class 0000: 1106:3057
pciDolphinFixup: 10ec:8139 IRQ pin A-->B IRQ 10
pciDolphinFixup: 1106:3038 VIA device: IRQ 42 (i8259 IRQ 5)
Linux version 2.2.20 (root@MF-DEV-SSBUILD01) (ecc version v6.0_6127) #1 Wed Dec 15 13:10:43 CET 2010
CPU frequency: 297 MHz
Mem frequency: 118 MHz
Calibrating delay loop... 296.55 BogoMIPS
Memory: 96128k/130032k available (2736k kernel code, 1072k data, 400k reserved)
Dentry hash table entries: 16384 (order 3, 128k)
Buffer cache hash table entries: 524288 (order 7, 2048k)
Page cache hash table entries: 8192 (order 1, 32k)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
TCP: Hash tables configured (ehash 524288 bhash 65536)
Serial driver version 4.27 with no serial options enabled
ttyS00 at 0x03f8 (irq = 41) is a 16550A
ttyS01 at 0x02f8 (irq = 40) is a 16550A
pty: 256 Unix98 ptys configured
RAM disk driver initialized:  16 RAM disks of 29696K size
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 29696 blocks [1 disk] into ram disk... done.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb.c: registered new driver hid
mice: PS/2 mouse device common for all mice
usb-uhci.c: $Revision: 1.2 $ time 13:11:06 Dec 15 2010
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0x1120, IRQ 42
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
usb.c: USB new device connect, assigned device number 1
Product: USB UHCI Root Hub
SerialNumber: 1120
hub.c: USB hub found
hub.c: 2 ports detected
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 128k freed
Using /lib/modules/2.2.20/block/doc.o
fl: TrueFFS driver 621.41
flRegisterComponents: fFound:01
fl: 1 device(s) found
fl: Registered module at major 62
Partition check:
 fla: fla1
fl: Device 0x0 size 0x1028000 sectors 0x8140
fl:     partition 0x1 size 0x1024c00
 fla: fla1
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
EXT2-fs error (device fl(62,1)): ext2_check_blocks_bitmap: Wrong free blocks count for group 0, stored = 2798, counted = 2800
EXT2-fs error (device fl(62,1)): ext2_check_blocks_bitmap: Wrong free blocks count in super block, stored = 10727, counted = 10729
EXT2-fs error (device fl(62,1)): ext2_check_inodes_bitmap: Wrong free inodes count in group 0, stored = 2039, counted = 2041
EXT2-fs error (device fl(62,1)): ext2_check_inodes_bitmap: Wrong free inodes count in super block, stored = 4111, counted = 4113
grep: /var/run/rc.pids: No such file or directory
test: 0: unknown operand
ifconfig: face: error fetching interface information: Device not found
 
Using /lib/modules/2.2.20/8139too.o
PCI: Increasing latency timer of device 00:50 to 64
eth0: 8139too Fast Ethernet driver 0.9.18-2.2
eth0: Samsung Electronics SMT-6000E, YSU v1.2 <sukun.yoon@samsung.com>
eth0: RealTek RTL8139 Fast Ethernet board found at 0x1000, IRQ 10
eth0: Chip is 'RTL-8139C' - MAC address '00:00:f0:ef:7e:56'.
ifconfig: face: error fetching interface information: Device not found
 
60: old priority 0, new priority 7
eth0: Setting half-duplex based on auto-negotiated partner ability 0000.
Using /lib/modules/2.2.20/saa7128/saa7128.o
Loading Saa7128 Color Bar Test Module
Saa7128color: Device registered with Major Number = 0
Using /lib/modules/2.2.20/saa7128/cxa2161r.o
^ALoading Cxa2161r Scart Switch Test Module
Cxa2161rScart: Device registered with Major Number = 0
connect: Network is unreachable
cat: /proc/bus/usb/devices: No such file or directory
rm: cannot remove `/wfs/run': No such file or directory
Login: killall: Evo: no process killed
ifconfig: face: error fetching interface information: Device not found
 
Using /lib/modules/2.2.20/pageCluster.o
Using /lib/modules/2.2.20/KernelEvents.o
Using /lib/modules/2.2.20/processInfo.o
Using /lib/modules/2.2.20/ProcessInfoDrv.o
Using /lib/modules/2.2.20/EventDrv.o
Using /lib/modules/2.2.20/PageClusterDrv.o
^[[5~Using /lib/modules/2.2.20/noncoregpDev.o
Using /lib/modules/2.2.20/boardSupportDev.o
Success1 registering the  Video DAC devices for board: 1300, daughter board: 0
Success2 registering the  Video DAC devices for board: 1300, daughter board: 0
Success3 registering the  Video DAC devices for board: 1300, daughter board: 0
Using /lib/modules/2.2.20/dmaBuffers.o
Using /lib/modules/2.2.20/streaming.o
Using /lib/modules/2.2.20/mediaDev.o
Jump starting VLX processor In 6.0 mode.
Vlx processor started successfully (vlxStatus 0x2).
Using /lib/modules/2.2.20/ScrDrv.o
Using /lib/modules/2.2.20/AoutDrv.o
Using /lib/modules/2.2.20/DrcDrv.o
Using /lib/modules/2.2.20/DmaBufferDrv.o
Using /lib/modules/2.2.20/cs4341/cs4341Control.o
Using /lib/modules/2.2.20/IrDrv.o
REAL POOL 0x2d00008 to 0x2d00008. Heap at 0x1075524
REAL MALLOC 0x2d00008
REAL POOL 0x2d00008 to 0x2d00028. Heap at 0x1075524
REAL MALLOC 0x2d00028
REAL POOL 0x2d00008 to 0x2d00038. Heap at 0x1075524
REAL MALLOC 0x2d00038
REAL FREE (nil)
REAL POOL 0x2d00008 to 0x2d00130. Heap at 0x1075524
REAL MALLOC 0x2d00130
REAL POOL 0x2d00008 to 0x2aab0008. Heap at 0x1075524
REAL MALLOC 0x2aab0008
REAL POOL 0x2d00008 to 0x2aab0008. Heap at 0x1075524
REAL MALLOC 0x2d00960
Saa7128color : Device Open (254, 0)
Saa7128color: Opened Value 0
Enter SamsungPlayer:0
TVmode select: 4:3 TV
^[[5~Login: IIS audclk = 1
audclk = 1
DrcDrv: Output -> PAL Interlaced 720 x 576 @ 25Hz
 
  Primary input:   Enabled
  Secondary input: Enabled
  Graphics input:  Enabled
  gfxFormat:       800
  alphaStream:     0
WARNING: Unable to utilize DMA pool. Defaulted to alloc for 1658880 bytes. This is OK during Evo init.
Cxa2161rScart : Device Open (252, 0)
Cxa2161rScart: Opened Value 0
 
I2C_ADDR - DATA1, DATA2, DATA3, DATA4, DATA5, DATA6, DATA7
  [90]       86 ,   80,    00 ,   33 ,   00 ,   0b ,   ef
 
I2C_ADDR - DATA1, DATA2, DATA3, DATA4, DATA5, DATA6, DATA7
  [90]       86 ,   80,    00 ,   33 ,   00 ,   0b ,   ef
                        ZCS POD     S/D FNC_VCR
                 7 - 6 - 5 - 4 - 3 - 2 - 1 - 0
CXA2161R STATUS: 1 - 1 - 1 - 1 - 1 - 0 - 0 - 0

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

147

148

149

150

151

152

153

154

155

156

157

158

159

160

161

162

163

164

165

166

167

168

169

170

171

172

173

174

175

176

177

178

179

180

181

182

183

184

185

186

187

188

189

190

191

192

193

194

195

196

197

198

199

200

Success1 registering the Video DAC devices for board: 1300, daughter board: 0

Success2 registering the Video DAC devices for board: 1300, daughter board: 0

Success3 registering the Video DAC devices for board: 1300, daughter board: 0

[cyg_net_init] Init: mbinit(0x00000000)

[cyg_net_init] Init: cyg_net_init_devs(0x00000000)

Init device 'rltk8139_eth0'

[cyg_net_init] Init: loopattach(0x00000000)

[cyg_net_init] Init: ifinit(0x00000000)

[cyg_net_init] Init: domaininit(0x00000000)

[cyg_net_init] Init: cyg_net_add_domain(0x803afae0)

New domain internet at 0x00000000

[cyg_net_init] Init: cyg_net_add_domain(0x803aea60)

New domain route at 0x00000000

[cyg_net_init] Init: call_route_init(0x00000000)

[cyg_net_init] Done

*************************

* Bootrom Version *

* V_STB_BT_01_02_050418 *

*************************

pciVIAInit

imageDisplay

Display Refresh Video Output example.

etiDefaultMemPool 0x87efc000 , start 0x80000000 size 0x8000000 hiMemGap 0x104000

xOffset 80 yOffset 48 dstBytesPerPixel 2 imageBmpWidth 640

CXA2161R status : d8

Press <CANCEL> remote key to start net booting....

hmpv_read_fcnt

start time in 23eab437 cycles

Doc Booting....

flRegisterSAFTL: start

flRegisterSAFTL: end

Media Size = 32 Mbytes

Note: Searching for the media header.

As a result a few H/W protection error messages might be reported.

ERROR in read_Seq: M512_checkAndFixAccessError:Protection error occurred.

Note: header was found - end of media header search.

DALN: PC=0x8009938c, RP=0x800ff560, addr=0x80a19f39: 2 byte load r60

START WITH BANK0

imageversion : 0

START TIME : 26940493

bdkReadBlock has Completed Succefully

CheckSignature returned 0, nds signature passed

END TIME : b156d10e

Read done in 8d7d1a30 cycles

Start Booting.... address from [82217820]

00:0a:0 Class 0200: 10ec:8139 0:0x1000[256]I 1:0x10000000[256]M IRQ 9

00:0c:0 Class 0601: 1106:0686

00:0c:1 Class 0101: 1106:0571 4:0x1100[16]I

00:0c:2 Class 0c03: 1106:3038 4:0x1120[32]I IRQ 16

00:0c:4 Class 0000: 1106:3057

pciDolphinFixup: 10ec:8139 IRQ pin A-->B IRQ 10

pciDolphinFixup: 1106:3038 VIA device: IRQ 42 (i8259 IRQ 5)

Linux version 2.2.20 (root@MF-DEV-SSBUILD01) (ecc version v6.0_6127) #1 Wed Dec 15 13:10:43 CET 2010

CPU frequency: 297 MHz

Mem frequency: 118 MHz

Calibrating delay loop... 296.55 BogoMIPS

Memory: 96128k/130032k available (2736k kernel code, 1072k data, 400k reserved)

Dentry hash table entries: 16384 (order 3, 128k)

Buffer cache hash table entries: 524288 (order 7, 2048k)

Page cache hash table entries: 8192 (order 1, 32k)

POSIX conformance testing by UNIFIX

PCI: Probing PCI hardware

Linux NET4.0 for Linux 2.2

Based upon Swansea University Computer Society NET3.039

NET4: Unix domain sockets 1.0 for Linux NET4.0.

NET4: Linux TCP/IP 1.0 for NET4.0

IP Protocols: ICMP, UDP, TCP, IGMP

TCP: Hash tables configured (ehash 524288 bhash 65536)

Serial driver version 4.27 with no serial options enabled

ttyS00 at 0x03f8 (irq = 41) is a 16550A

ttyS01 at 0x02f8 (irq = 40) is a 16550A

pty: 256 Unix98 ptys configured

RAM disk driver initialized: 16 RAM disks of 29696K size

RAMDISK: ext2 filesystem found at block 0

RAMDISK: Loading 29696 blocks [1 disk] into ram disk... done.

usb.c: registered new driver usbdevfs

usb.c: registered new driver hub

usb.c: registered new driver hid

mice: PS/2 mouse device common for all mice

usb-uhci.c: $Revision: 1.2 $ time 13:11:06 Dec 15 2010

usb-uhci.c: High bandwidth mode enabled

usb-uhci.c: USB UHCI at I/O 0x1120, IRQ 42

usb-uhci.c: Detected 2 ports

usb.c: new USB bus registered, assigned bus number 1

usb.c: USB new device connect, assigned device number 1

Product: USB UHCI Root Hub

SerialNumber: 1120

hub.c: USB hub found

hub.c: 2 ports detected

VFS: Mounted root (ext2 filesystem).

Freeing unused kernel memory: 128k freed

Using /lib/modules/2.2.20/block/doc.o

fl: TrueFFS driver 621.41

flRegisterComponents: fFound:01

fl: 1 device(s) found

fl: Registered module at major 62

Partition check:

fla: fla1

fl: Device 0x0 size 0x1028000 sectors 0x8140

fl: partition 0x1 size 0x1024c00

fla: fla1

EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended

EXT2-fs error (device fl(62,1)): ext2_check_blocks_bitmap: Wrong free blocks count for group 0, stored = 2798, counted = 2800

EXT2-fs error (device fl(62,1)): ext2_check_blocks_bitmap: Wrong free blocks count in super block, stored = 10727, counted = 10729

EXT2-fs error (device fl(62,1)): ext2_check_inodes_bitmap: Wrong free inodes count in group 0, stored = 2039, counted = 2041

EXT2-fs error (device fl(62,1)): ext2_check_inodes_bitmap: Wrong free inodes count in super block, stored = 4111, counted = 4113

grep: /var/run/rc.pids: No such file or directory

test: 0: unknown operand

ifconfig: face: error fetching interface information: Device not found

Using /lib/modules/2.2.20/8139too.o

PCI: Increasing latency timer of device 00:50 to 64

eth0: 8139too Fast Ethernet driver 0.9.18-2.2

eth0: Samsung Electronics SMT-6000E, YSU v1.2 <sukun.yoon@samsung.com>

eth0: RealTek RTL8139 Fast Ethernet board found at 0x1000, IRQ 10

eth0: Chip is 'RTL-8139C' - MAC address '00:00:f0:ef:7e:56'.

ifconfig: face: error fetching interface information: Device not found

60: old priority 0, new priority 7

eth0: Setting half-duplex based on auto-negotiated partner ability 0000.

Using /lib/modules/2.2.20/saa7128/saa7128.o

Loading Saa7128 Color Bar Test Module

Saa7128color: Device registered with Major Number = 0

Using /lib/modules/2.2.20/saa7128/cxa2161r.o

^ALoading Cxa2161r Scart Switch Test Module

Cxa2161rScart: Device registered with Major Number = 0

connect: Network is unreachable

cat: /proc/bus/usb/devices: No such file or directory

rm: cannot remove `/wfs/run': No such file or directory

ifconfig: face: error fetching interface information: Device not found

Using /lib/modules/2.2.20/pageCluster.o

Using /lib/modules/2.2.20/KernelEvents.o

Using /lib/modules/2.2.20/processInfo.o

Using /lib/modules/2.2.20/ProcessInfoDrv.o

Using /lib/modules/2.2.20/EventDrv.o

Using /lib/modules/2.2.20/PageClusterDrv.o

^[[5~Using /lib/modules/2.2.20/noncoregpDev.o

Using /lib/modules/2.2.20/boardSupportDev.o

Success1 registering the Video DAC devices for board: 1300, daughter board: 0

Success2 registering the Video DAC devices for board: 1300, daughter board: 0

Success3 registering the Video DAC devices for board: 1300, daughter board: 0

Using /lib/modules/2.2.20/dmaBuffers.o

Using /lib/modules/2.2.20/streaming.o

Using /lib/modules/2.2.20/mediaDev.o

Jump starting VLX processor In 6.0 mode.

Vlx processor started successfully (vlxStatus 0x2).

Using /lib/modules/2.2.20/ScrDrv.o

Using /lib/modules/2.2.20/AoutDrv.o

Using /lib/modules/2.2.20/DrcDrv.o

Using /lib/modules/2.2.20/DmaBufferDrv.o

Using /lib/modules/2.2.20/cs4341/cs4341Control.o

Using /lib/modules/2.2.20/IrDrv.o

REAL POOL 0x2d00008 to 0x2d00008. Heap at 0x1075524

REAL MALLOC 0x2d00008

REAL POOL 0x2d00008 to 0x2d00028. Heap at 0x1075524

REAL MALLOC 0x2d00028

REAL POOL 0x2d00008 to 0x2d00038. Heap at 0x1075524

REAL MALLOC 0x2d00038

REAL FREE (nil)

REAL POOL 0x2d00008 to 0x2d00130. Heap at 0x1075524

REAL MALLOC 0x2d00130

REAL POOL 0x2d00008 to 0x2aab0008. Heap at 0x1075524

REAL MALLOC 0x2aab0008

REAL POOL 0x2d00008 to 0x2aab0008. Heap at 0x1075524

REAL MALLOC 0x2d00960

Saa7128color : Device Open (254, 0)

Saa7128color: Opened Value 0

Enter SamsungPlayer:0

TVmode select: 4:3 TV

^[[5~Login: IIS audclk = 1

audclk = 1

DrcDrv: Output -> PAL Interlaced 720 x 576 @ 25Hz

Primary input: Enabled

Secondary input: Enabled

Graphics input: Enabled

gfxFormat: 800

alphaStream: 0

WARNING: Unable to utilize DMA pool. Defaulted to alloc for 1658880 bytes. This is OK during Evo init.

Cxa2161rScart : Device Open (252, 0)

Cxa2161rScart: Opened Value 0

I2C_ADDR - DATA1, DATA2, DATA3, DATA4, DATA5, DATA6, DATA7

[90] 86 , 80, 00 , 33 , 00 , 0b , ef

I2C_ADDR - DATA1, DATA2, DATA3, DATA4, DATA5, DATA6, DATA7

[90] 86 , 80, 00 , 33 , 00 , 0b , ef

ZCS POD S/D FNC_VCR

7 - 6 - 5 - 4 - 3 - 2 - 1 - 0

CXA2161R STATUS: 1 - 1 - 1 - 1 - 1 - 0 - 0 - 0

KPN Experia Box (Arcadyan ARV7519) – UART aansluiting

Door Sebastiaan Geplaatst op 2016-01-14 Geplaatst in KPN Tagged with Arcadyan ARV7519, Bootlog, Experia Box, Firmware, KPN, PW22, Router, UART, WLAN

Loshalen De KPN Experia Box (Arcadyan ARV7519) is makkelijk los te maken, je moet de 2 schroefjes losdraaien aan de …

KPN Experia Box (Arcadyan ARV7519) – UART aansluiting Lees meer »

KPN Experia Box (Arcadyan ARV7519) – Bootlog via UART

Door Sebastiaan Geplaatst op 2016-01-13 Geplaatst in KPN Tagged with Arcadyan ARV7519, Bootlog, Experia Box, Firmware, KPN, PW22, Router, UART, WLAN

Bootlog via UART Dit is de bootlog bij het opstarten via de UART seriele verbinding op de printplaat.

ROM VER: 1.0.3
CFG 01
Read EEPROMX
 X



=======================================================================
Wireless ADSL Gateway DANUBE Loader v2.00.12 build Jan 17 2011 17:15:51
                    Arcadyan Technology Corporation
=======================================================================
EON EN29LV640L top boot 16-bit mode found

Copying boot params.....DONE


Press Space Bar 3 times to enter command mode ...
Flash Checking [0] Passed.
Image[1] at 0xb0100000, len:1868317, type:0
Image[2] at 0xb02c8400, len:6928, type:10
Image[3] at 0xb02ca000, len:224436, type:11
Image[4] at 0xb0301000, len:227009, type:12
Image[5] at 0xb0338800, len:168592, type:50
Image[6] at 0xb0361c00, len:452618, type:90
Firmware image at 0, ART image at -1

Run-up Normal Firmware...

Unzipping firmware [0(5)] at 0x80002000 ... [ZIP 3] [ZIP 1]  done
Run-time code running ...

In c_entry() function ...
install_exception
Co config = 80008483
[INIT] Interrupt ...
##### _ftext      = 0x80002000
##### _fdata      = 0x80723F10
##### __bss_start = 0x807F6A94
##### end         = 0x8330B280
allocate_memory_after_end> len 863108, ptr 0x83313280
##### Backup Data from 0x80723F10 to 0x83313280~0x833E5E04 len 863108
##### Backup Data completed
##### Backup Data verified
EON EN29LV640L top boot 16-bit mode found
new bootcode format
[GPIO FLOW] SetGpio() Begin ..
gptu: totally 6 16-bit timers/counters
Init timer = 0
[GPIO FLOW] SetGpio() End.
[INIT] System Log Pool startup ...
[INIT] MTinitialize ..
[INIT] usrclk
CPU Clock 333333334 Hz
mips_counter_frequency:166666667
r4k_offset: 00028b0a(166666)
init_US_counter : time1 = 260456 , time2 = 40260479, diff 40000023
US_counter = 48
 cnt1 40987750 cnt2 40990007, diff 2257
Runtime code version: 01.01.121
System startup...
[INIT] Memory COLOR 0, 3000000 bytes ..
[INIT] Memory COLOR 1, 262144 bytes ..
[INIT] Memory COLOR 2, 4565152 bytes ..
EON EN29LV640L top boot 16-bit mode found

ROM VER: 1.0.3

CFG 01

Read EEPROMX

=======================================================================

Wireless ADSL Gateway DANUBE Loader v2.00.12 build Jan 17 2011 17:15:51

Arcadyan Technology Corporation

=======================================================================

EON EN29LV640L top boot 16-bit mode found

Copying boot params.....DONE

Press Space Bar 3 times to enter command mode ...

Flash Checking [0] Passed.

Image[1] at 0xb0100000, len:1868317, type:0

Image[2] at 0xb02c8400, len:6928, type:10

Image[3] at 0xb02ca000, len:224436, type:11

Image[4] at 0xb0301000, len:227009, type:12

Image[5] at 0xb0338800, len:168592, type:50

Image[6] at 0xb0361c00, len:452618, type:90

Firmware image at 0, ART image at -1

Run-up Normal Firmware...

Unzipping firmware [0(5)] at 0x80002000 ... [ZIP 3] [ZIP 1] done

Run-time code running ...

In c_entry() function ...

install_exception

Co config = 80008483

[INIT] Interrupt ...

##### _ftext = 0x80002000

##### _fdata = 0x80723F10

##### __bss_start = 0x807F6A94

##### end = 0x8330B280

allocate_memory_after_end> len 863108, ptr 0x83313280

##### Backup Data from 0x80723F10 to 0x83313280~0x833E5E04 len 863108

##### Backup Data completed

##### Backup Data verified

EON EN29LV640L top boot 16-bit mode found

new bootcode format

[GPIO FLOW] SetGpio() Begin ..

gptu: totally 6 16-bit timers/counters

Init timer = 0

[GPIO FLOW] SetGpio() End.

[INIT] System Log Pool startup ...

[INIT] MTinitialize ..

[INIT] usrclk

CPU Clock 333333334 Hz

mips_counter_frequency:166666667

r4k_offset: 00028b0a(166666)

init_US_counter : time1 = 260456 , time2 = 40260479, diff 40000023

US_counter = 48

cnt1 40987750 cnt2 40990007, diff 2257

Runtime code version: 01.01.121

System startup...

[INIT] Memory COLOR 0, 3000000 bytes ..

[INIT] Memory COLOR 1, 262144 bytes ..

[INIT] Memory COLOR 2, 4565152 bytes ..

EON EN29LV640L top boot 16-bit mode found

RESET …

KPN Experia Box (Arcadyan ARV7519) – Bootlog via UART Lees meer »

Fritz!Box Fon WLAN 7170 – Bootlog via UART

Door Sebastiaan Geplaatst op 2015-04-15 Geplaatst in FRITZ!Box Tagged with 7170, Bootlog, Firmware, Fon, Fritz!Box, Router, UART, Wireless, WLAN

Fritz!Box Fon WLAN 7170 Router Bootlog via UART Dit is de bootlog bij het opstarten via de UART seriele …

Fritz!Box Fon WLAN 7170 – Bootlog via UART Lees meer »

Zoeken

Tag: Bootlog

Linksys SRW2008x (managed switch) – Webinterface

Linksys SRW2008x (managed switch) – Bootlog

Linksys WAG354G (ADSL router) – Bootlog via UART

Samsung SMT-6010E – Firmware

Samsung SMT-6010E – Linux gegevens

Samsung SMT-6010E – Aansluiten via UART

Samsung SMT-6010E – Boot LOG (UART)

KPN Experia Box (Arcadyan ARV7519) – UART aansluiting

KPN Experia Box (Arcadyan ARV7519) – Bootlog via UART

Fritz!Box Fon WLAN 7170 – Bootlog via UART