switch Archieven - DomoticX Knowledge Center

Linksys SRW2008x (managed switch) Bootlog

------ Performing the Power-On Self Test (POST) ------

UART Channel Loopback Test........................PASS

Testing the System SDRAM..........................PASS

Boot1 Checksum Test...............................PASS

Boot2 Checksum Test...............................PASS

Flash Image Validation Test.......................PASS



BOOT Software Version 1.0.1 Built  06-Jun-2006  17:23:21

:::
:::        ::: :::       ::: :::     :::::  :::::::::: :::      ::: ::::::::::
:::        ::: :::::     ::: :::   :::::   ::::     ::: ::::  :::: ::::     :::
:::        ::: ::: :::   ::: ::::::::      ::::          ::::::::  ::::
:::        ::: :::   ::  ::: ::::::::::     ::::::::::     ::::     ::::::::::
:::        ::: :::    :::::: :::    ::::            :::    ::::             :::
:::::::::: ::: :::      :::: :::      :::: :::......:::    ::::    :::......:::
 ......... ... ...       ... ...       .... ..........     ....     ..........

Linksys SmartSwitch SRW208 based on 88E6218 with ARM946E-S.
32MByte SDRAM. I-Cache 8 KB. D-Cache 8 KB. Cache Enabled.

Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.
Preparing to decompress...
 100%
Decompressing SW from flash
 100%

OK
Running from RAM...

******************************************************************
*** Running  SW  Ver. 1.0.4  Date  06-Sep-2007  Time  09:11:40 ***
******************************************************************

HW version is 00.03.00
Base Mac address is: 00:22:6b:c0:79:d1
Dram size is  : 32M bytes
Dram first block size is  : 17152K bytes
Dram first PTR is  : 0xF40000
Flash size is: 8M
01-Jan-2000 01:01:05 %CDB-I-LOADCONFIG: Loading startup configuration.
Device configuration:
PCB revision: 1
Slot 1 - SRW2008MP HW Rev.  0.1
Tapi Version: v1.3.3.1
Core Version: v1.3.3.1
01-Jan-2000 01:01:19 %INIT-I-InitCompleted: Initialization task is completed


                          Login Screen
                          ============


                       User Name:

                       Password:

------ Performing the Power-On Self Test (POST) ------

UART Channel Loopback Test........................PASS

Testing the System SDRAM..........................PASS

Boot1 Checksum Test...............................PASS

Boot2 Checksum Test...............................PASS

Flash Image Validation Test.......................PASS

BOOT Software Version 1.0.1 Built 06-Jun-2006 17:23:21

:::

::: ::: ::: ::: ::: ::::: :::::::::: ::: ::: ::::::::::

::: ::: ::::: ::: ::: ::::: :::: ::: :::: :::: :::: :::

::: ::: ::: ::: ::: :::::::: :::: :::::::: ::::

::: ::: ::: :: ::: :::::::::: :::::::::: :::: ::::::::::

::: ::: ::: :::::: ::: :::: ::: :::: :::

:::::::::: ::: ::: :::: ::: :::: :::......::: :::: :::......:::

......... ... ... ... ... .... .......... .... ..........

Linksys SmartSwitch SRW208 based on 88E6218 with ARM946E-S.

32MByte SDRAM. I-Cache 8 KB. D-Cache 8 KB. Cache Enabled.

Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.

Preparing to decompress...

100%

Decompressing SW from flash

100%

Running from RAM...

******************************************************************

*** Running SW Ver. 1.0.4 Date 06-Sep-2007 Time 09:11:40 ***

******************************************************************

HW version is 00.03.00

Base Mac address is: 00:22:6b:c0:79:d1

Dram size is : 32M bytes

Dram first block size is : 17152K bytes

Dram first PTR is : 0xF40000

Flash size is: 8M

01-Jan-2000 01:01:05 %CDB-I-LOADCONFIG: Loading startup configuration.

Device configuration:

PCB revision: 1

Slot 1 - SRW2008MP HW Rev. 0.1

Tapi Version: v1.3.3.1

Core Version: v1.3.3.1

01-Jan-2000 01:01:19 %INIT-I-InitCompleted: Initialization task is completed

============

User Name:

Password:

Hardware info

                                Versions
                                ========

  Boot Version:          1.0.1 (Date:  06-Jun-2006, Time:  17:23:21)

  Software Version:      1.0.4 (Date:  06-Sep-2007, Time:  09:11:40)

  Hardware Version:      00.03.00


                          General System Information
                          ==========================

  System Description:    SRW2008MP - 6-port Gigabit Switch with 2 Combo ports,

  System Up Time:        0,00:05:20 (days,hour:min:sec)

  System MAC Address:    00:22:6b:c0:79:d1

  System Contact:

  System Name:

  System Location:

Versions

========

Boot Version: 1.0.1 (Date: 06-Jun-2006, Time: 17:23:21)

Software Version: 1.0.4 (Date: 06-Sep-2007, Time: 09:11:40)

Hardware Version: 00.03.00

General System Information

==========================

System Description: SRW2008MP - 6-port Gigabit Switch with 2 Combo ports,

System Up Time: 0,00:05:20 (days,hour:min:sec)

System MAC Address: 00:22:6b:c0:79:d1

System Contact:

System Name:

System Location:

Linksys SRW2008x (managed switch) De firmware is te updaten via de webinterface: Voltooid

SRW2008/SRW2008P/SRW2008MP Firmware Release Note
Software version 1.0.4 09/11/2007
Boot version 1.0.1 06/13/2006
==========
1. Support of 100SFP
This release introduces an enhancement to support 100SFP module. The device can
automatically set up proper port setting for supported 100SFP modules: Linksys
MFELX1 and MFEFX1.
.
2. CPU Utilization Display
The application provides the ability to enable and disable the CPU utilization
mechanism and display its output. This application is controlled by WEB base
management to display the system CPU utilization. The display will be graphic,
showing history point per second over the user-selected period. If Java Virtual
Machine (JVM) is not installed on the client PC, the graph is not displayed.
Refer the link of http://www.java.com for JVM installation.
3. Power allocation per Port – SRW2008P,SRW2008MP
With this software release an enhancement to the PoE standard is introduced,
whereby the user configures the allocated power. If a Power Device (PD) on a PoE
port consumes more power than the specified allocate power, the port will be
shut down. If the user does not configure the power allocation, the PoE
classification is kept.
4. Total PoE Power set the max capacity- SRW2008P
Starting this release, one can upgrade the SRW2008P to support full power
allocation for all eight ports. After connecting the power supply of
SRW2008MP/SRW208MP, the user can use the web interface of Port Management--> PoE
Power setting to select “Extended” on the Power Supply Type drop-down menu.
Known Issues
=========
1. ACL --> MAC Based ACL
Creating a MAC ACL with to permit ethertype 0800 causes all traffic to be
forwarded. Configuring a MAC ACL to permit ethertype 86DD causes all traffic to
be denied.
Recommended Workaround: To avoid these situations, add a rule to deny any any.
2 . Setup --> network setting
Changing any field on the Network Settings Tab will result in sending a DHCP
release and than Discover which may lead to in IP address change.
3. Admin --> Cable Test
When testing cable with advanced test only (without simple test before), the
results are incorrect.
4. Admin --> Port Mirroring
After configuring port monitoring, the target port is grayed out, and cannot be
modified.
Recommended Workaround: Delete the mirroring session, and reconfigure.
5. QoS --> Basic Mode (Double Check this Bug) 
The "Trust Mode Table" is not functional. Attempting to disable the trust mode
on an interface of the trust mode table results in an error message, and does
not disable the trust mode on a per port basis.
6. QoS --> Advanced Mode
(a) Newly created entries in the Advanced Mode are displayed in the table only
after refreshing the table. For example, after creating a new policy, using the
pop-up window, it is displayed only after refreshing the main window.
(b) Under one policy, one can only select either Single or Aggregate police type
but not both.
(c) It is not possible to create two identical policers with the same settings
and action.
(d) QoS advanced mode page will refresh twice if browsed to it.
7. Security --> TACACS+
It is impossible to update the key string, after a server has already been
configured.
Recommended Workaround: To update the key string, the server must be deleted,
and then re-configured.
8. Setup --> Time
(a) The DST dates cannot be edited after selecting different radio boxes.
Recommended Workaround: Refresh the page, and configure.
(b) Configuring Daylight Savings Time in conjunction with SNTP servers may
result in unclear errors.
(c) The prioritization between servers is not maintained when two servers are
configured simultaneously.
(d) If a lower IP address is added after the first one was configured and saved,
then the two IP addresses swap location and prioritization.
9. SNMP --> Communities
 To edit fields including the change of SNMP mode, the entry needs to be
deleted, and then re-entered.
10. SNMP --> Group Membership
It is not possible to modify the user name after it has been entered.
Recommended Workaround: Delete the user and reconfigure.
11. Image Download
When downloading via tftp or http, performing Power off/on to the device may
result in requirement for downloading the image via XMODEM after the device
recovers. When downloading via XModem, the device recovers by itself.
Note: Avoid disconnecting the device from a power source during image upload
12. Timestamps
The order of the month and day in the dates presented in syslog messages is the
European fromat (dd/mm/yy), and not the US format.
13. Security--> Storm Control (Need to double check)
Configuring Unknown Unicast mode results in an error message.
14. Web browser availability
The web management interface is best viewed using Internet Explorer 5.5 and up,
with a resolution of 1024 x 768. In the current software version, certain pages
cannot be viewed well using other browsers. It is recommended to apply the
following workarounds. 
Note: Internet Explorer web browser must be installed prior to running the
following procedures.
-Using Mozilla Firefox Web Browser:
(a) Install Firefox "IE Tab" add-ons. The latest version is available on
https://addons.mozilla.org/firefox/1419/
(b) Select Tools --> IE Tab. Add in the IP address of switches to Sites Fitters
 (e.g. “http://172.18.1.27” accepts wildcard http://172.18.1.*).
(c) Ensure that cookies are enabled, by clicking "enable" to "All sites to set
cookies"Tools -> Options -> Privacy -> Cookies.
-Using Netscape Web Browser: Click the icon in the left corner, and select "IE
Display".
15. Management --> Password
User can not change the default password from the web UI
Recommended Workaround: Use the console menu
16. VLAN Management --> VLAN to Port
When VLAN to Port is set the action is performed successfully and then an error
message is displayed on the window.
Recommended Workaround: Ignore error message

100

101

102

103

104

105

106

107

108

109

110

SRW2008/SRW2008P/SRW2008MP Firmware Release Note

Software version 1.0.4 09/11/2007

Boot version 1.0.1 06/13/2006

==========

1. Support of 100SFP

This release introduces an enhancement to support 100SFP module. The device can

automatically set up proper port setting for supported 100SFP modules: Linksys

MFELX1 and MFEFX1.

2. CPU Utilization Display

The application provides the ability to enable and disable the CPU utilization

mechanism and display its output. This application is controlled by WEB base

management to display the system CPU utilization. The display will be graphic,

showing history point per second over the user-selected period. If Java Virtual

Machine (JVM) is not installed on the client PC, the graph is not displayed.

Refer the link of http://www.java.com for JVM installation.

3. Power allocation per Port – SRW2008P,SRW2008MP

With this software release an enhancement to the PoE standard is introduced,

whereby the user configures the allocated power. If a Power Device (PD) on a PoE

port consumes more power than the specified allocate power, the port will be

shut down. If the user does not configure the power allocation, the PoE

classification is kept.

4. Total PoE Power set the max capacity- SRW2008P

Starting this release, one can upgrade the SRW2008P to support full power

allocation for all eight ports. After connecting the power supply of

SRW2008MP/SRW208MP, the user can use the web interface of Port Management--> PoE

Power setting to select “Extended” on the Power Supply Type drop-down menu.

Known Issues

=========

1. ACL --> MAC Based ACL

Creating a MAC ACL with to permit ethertype 0800 causes all traffic to be

forwarded. Configuring a MAC ACL to permit ethertype 86DD causes all traffic to

be denied.

Recommended Workaround: To avoid these situations, add a rule to deny any any.

2 . Setup --> network setting

Changing any field on the Network Settings Tab will result in sending a DHCP

release and than Discover which may lead to in IP address change.

3. Admin --> Cable Test

When testing cable with advanced test only (without simple test before), the

results are incorrect.

4. Admin --> Port Mirroring

After configuring port monitoring, the target port is grayed out, and cannot be

modified.

Recommended Workaround: Delete the mirroring session, and reconfigure.

5. QoS --> Basic Mode (Double Check this Bug)

The "Trust Mode Table" is not functional. Attempting to disable the trust mode

on an interface of the trust mode table results in an error message, and does

not disable the trust mode on a per port basis.

6. QoS --> Advanced Mode

(a) Newly created entries in the Advanced Mode are displayed in the table only

after refreshing the table. For example, after creating a new policy, using the

pop-up window, it is displayed only after refreshing the main window.

(b) Under one policy, one can only select either Single or Aggregate police type

but not both.

and action.

(d) QoS advanced mode page will refresh twice if browsed to it.

7. Security --> TACACS+

It is impossible to update the key string, after a server has already been

configured.

Recommended Workaround: To update the key string, the server must be deleted,

and then re-configured.

8. Setup --> Time

(a) The DST dates cannot be edited after selecting different radio boxes.

Recommended Workaround: Refresh the page, and configure.

(b) Configuring Daylight Savings Time in conjunction with SNTP servers may

result in unclear errors.

configured simultaneously.

(d) If a lower IP address is added after the first one was configured and saved,

then the two IP addresses swap location and prioritization.

9. SNMP --> Communities

To edit fields including the change of SNMP mode, the entry needs to be

deleted, and then re-entered.

10. SNMP --> Group Membership

It is not possible to modify the user name after it has been entered.

Recommended Workaround: Delete the user and reconfigure.

11. Image Download

When downloading via tftp or http, performing Power off/on to the device may

result in requirement for downloading the image via XMODEM after the device

recovers. When downloading via XModem, the device recovers by itself.

Note: Avoid disconnecting the device from a power source during image upload

12. Timestamps

The order of the month and day in the dates presented in syslog messages is the

European fromat (dd/mm/yy), and not the US format.

13. Security--> Storm Control (Need to double check)

Configuring Unknown Unicast mode results in an error message.

14. Web browser availability

The web management interface is best viewed using Internet Explorer 5.5 and up,

with a resolution of 1024 x 768. In the current software version, certain pages

cannot be viewed well using other browsers. It is recommended to apply the

following workarounds.

Note: Internet Explorer web browser must be installed prior to running the

following procedures.

-Using Mozilla Firefox Web Browser:

(a) Install Firefox "IE Tab" add-ons. The latest version is available on

https://addons.mozilla.org/firefox/1419/

(b) Select Tools --> IE Tab. Add in the IP address of switches to Sites Fitters

(e.g. “http://172.18.1.27” accepts wildcard http://172.18.1.*).

cookies"Tools -> Options -> Privacy -> Cookies.

-Using Netscape Web Browser: Click the icon in the left corner, and select "IE

Display".

15. Management --> Password

User can not change the default password from the web UI

Recommended Workaround: Use the console menu

16. VLAN Management --> VLAN to Port

When VLAN to Port is set the action is performed successfully and then an error

message is displayed on the window.

Recommended Workaround: Ignore error message

Download firmware 1.04 @ software.cisco.com Download firmware 1.02 @ www.drewy.com Download PDF release notes @ cisco.com [#/firmware/linksys_swr2008x” ]

Zoeken

Tag: switch

Linksys SRW2008x (managed switch) – Webinterface

Linksys SRW2008x (managed switch) – Bootlog

Linksys SRW2008x (managed switch)

Linksys SRW2008x (managed switch) – Firmware

Raspberry Pi – Interrupts gebruiken met GPIO pinnen (Python)