The closer you look, the less you see!
Programmer Software Tools Package File name Description Version Date ICP_Programming_Tool_V3.02.6990.zip Supported Device and Revision History NuMicro ICP tool & user manual V3.02.6990 2020-5-13 ISP Programming Tool V3.05.zip Supported Device and Revision History NuMicro ISP programming tool & user manual V3.05 …
RD9700_Android_2.6.35 RD9700_Linux RD9700_MAC DRIVER RD9700_WINCE500 RD9700_WINCE600 RD9700_XP-WIN8-32 RD9700_XP-WIN8-64 RD9700_XP-WIN98 Setup
After you flashed the firmware with the “UnifiedEngineering” version, you can place a cold junction temperature sensor for better temperatur management. From github: The existing controller makes the assumption that the cold-junction is at 20 degrees Celsius at all times …
T-962 reflow oven 31 – Cold junction compensation Lees meer »
Firmware replacement The standard T-962 firmware is very simple and there are a few flaws in it (temperature overshoot, no coldjuntion compensation, no pwm controlled fan, etc). There is a opensource firmware build on github: https://github.com/UnifiedEngineering/T-962-improvements Github page T-962 reflow …
Informatie (ENG): LPC2000 flash utility is a software which is used to program LPC2000 series ARM microcontrollers: LPC2101, LPC2102, LPC2103, LPC2104, LPC2106, LPC2106, LPC2114, LPC2114, LPC2119, LPC2124, LPC2129, LPC2131, LPC2132, LPC2134, LPC2136, LPC2138, LPC2141, LPC2142, LPC2144, LPC2146, LPC2148, LPC2194. Programming …
Firmware Tool – Philips LPC2000 Flash Utility voor NXP microcontrollers (Windows) Lees meer »
Informatie (ENG): Flash Magic is a PC tool for programming flash based microcontrollers from NXP using a serial or Ethernet protocol while in the target hardware. NXP Semiconductors produce a range of Microcontrollers that feature both on-chip Flash memory and the ability to be …
Firmware Tool – FlashMagic voor NXP microcontrollers (Windows) Lees meer »
Ik heb deze afstandbediening aangeschaft voor diverse RC experimenten, op deze pagina vind je gevonden informatie. AFHDS 2A Door gebruik van de nieuwe AFHDS 2A schakelt deze zender razendsnel van de ene naar de andere frequentie binnen het 2.4GHz spectrum. De …
Informatie – Bricked printrboard verhelpen Je hebt wel eens van die momenten dat er wat misgaat met uploaden van firmware, resultaat is dan een “bricked” printrboard, geen COM poorten..niets meer… De oplossing is om via de ISP pinnen weer een …
Informatie – Firmware Met behulp van de volgende G-code commando’s kan men de firmware gegevens opvragen van de Builder 3D. Builder 3D Mono Model V2.1010C / Firmware V2.1010C (sticker) V2.1010B (firmware output)
|
1 2 3 4 5 6 7 8 9 10 11 |
start echo:PowerUp Brown out Reset Marlin 1.0.0 echo: Last Updated: Feb 6 2014 07:52:17 | Author: (none, default config) FIRMWARE_NAME:Marlin V1; Sprinter/grbl mashup for gen6 FIRMWARE_URL:http://www.3dprinter4U.com PROTOCOL_VERSION:V2.1010B MACHINE_TYPE:Builder EXTRUDER_COUNT:1 ok |
In repetier host:
|
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 |
echo:Stored settings retrieved echo:Steps per unit: echo: M92 X100.00 Y80.00 Z400.00 E50.00 echo:Maximum feedrates (mm/s): echo: M203 X500.00 Y500.00 Z5.00 E25.00 echo:Maximum Acceleration (mm/s2): echo: M201 X9000 Y9000 Z100 E10000 echo:Acceleration: S=acceleration, T=retract acceleration echo: M204 S3000.00 T3000.00 echo:Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum XY jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum E jerk (mm/s) echo: M205 S0.00 T0.00 B20000 X20.00 Z0.40 E5.00 echo:Home offset (mm): echo: M206 X0.00 Y0.00 Z0.00 echo:PID settings: echo: M301 P9.08 I0.42 D49.22 ok |
Deze instellingen vind je …
Informatie (ENG) grblForCyclone (ArSi) GRBL port for RAMPS and Sanguinololu boards. Original port was done by ArSi (read description) Modified again by Carlosgs to support RAMPS and Sanguinololu without any re-wiring (i.e. if MarlinForCyclone worked straight away, this one will). …