Firmware Archieven - Pagina 4 van 8 - DomoticX Knowledge Center

Plugwise Smile P1 – Firmware update disabled

Door Sebastiaan Geplaatst op 2016-06-09 Geplaatst in Plugwise - Smile P1 Getagd met Firmware, Plugwise, Smile P1, uploaden

Na een lange tijd weer even bezig met de PlugWise Smile P1, toch weer nieuwe dingetjes aan de horizon. Update disabled? Ik ga naar de link: http://192.168.x.x/update/firmware en zie staan:

<?xml version="1.0" encoding="ISO-8859-1"?>
<update>
	<firmware>
		<current>
			<version>2.0.62</version>
		</current>
		<upgrade>
			<state>update_disabled</state>
		</upgrade>
	</firmware>
</update>

<?xml version="1.0" encoding="ISO-8859-1"?>

</current>

<state>update_disabled</state>

</upgrade>

</firmware>

</update>

Ook in de portal bij status staat geen nieuwe firmware …

Plugwise Smile P1 – Firmware update disabled Lees meer »

Linksys SRW2008x (managed switch) – Bootlog

Door Sebastiaan Geplaatst op 2016-06-04 Geplaatst in Linksys Getagd met Bootlog, Firmware, Hardware info, Linksys, Managed switch, SRW2008x, switch

Linksys SRW2008x (managed switch) Bootlog

------ Performing the Power-On Self Test (POST) ------

UART Channel Loopback Test........................PASS

Testing the System SDRAM..........................PASS

Boot1 Checksum Test...............................PASS

Boot2 Checksum Test...............................PASS

Flash Image Validation Test.......................PASS



BOOT Software Version 1.0.1 Built  06-Jun-2006  17:23:21

:::
:::        ::: :::       ::: :::     :::::  :::::::::: :::      ::: ::::::::::
:::        ::: :::::     ::: :::   :::::   ::::     ::: ::::  :::: ::::     :::
:::        ::: ::: :::   ::: ::::::::      ::::          ::::::::  ::::
:::        ::: :::   ::  ::: ::::::::::     ::::::::::     ::::     ::::::::::
:::        ::: :::    :::::: :::    ::::            :::    ::::             :::
:::::::::: ::: :::      :::: :::      :::: :::......:::    ::::    :::......:::
 ......... ... ...       ... ...       .... ..........     ....     ..........

Linksys SmartSwitch SRW208 based on 88E6218 with ARM946E-S.
32MByte SDRAM. I-Cache 8 KB. D-Cache 8 KB. Cache Enabled.

Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.
Preparing to decompress...
 100%
Decompressing SW from flash
 100%

OK
Running from RAM...

******************************************************************
*** Running  SW  Ver. 1.0.4  Date  06-Sep-2007  Time  09:11:40 ***
******************************************************************

HW version is 00.03.00
Base Mac address is: 00:22:6b:c0:79:d1
Dram size is  : 32M bytes
Dram first block size is  : 17152K bytes
Dram first PTR is  : 0xF40000
Flash size is: 8M
01-Jan-2000 01:01:05 %CDB-I-LOADCONFIG: Loading startup configuration.
Device configuration:
PCB revision: 1
Slot 1 - SRW2008MP HW Rev.  0.1
Tapi Version: v1.3.3.1
Core Version: v1.3.3.1
01-Jan-2000 01:01:19 %INIT-I-InitCompleted: Initialization task is completed


                          Login Screen
                          ============


                       User Name:

                       Password:

------ Performing the Power-On Self Test (POST) ------

UART Channel Loopback Test........................PASS

Testing the System SDRAM..........................PASS

Boot1 Checksum Test...............................PASS

Boot2 Checksum Test...............................PASS

Flash Image Validation Test.......................PASS

BOOT Software Version 1.0.1 Built 06-Jun-2006 17:23:21

:::

::: ::: ::: ::: ::: ::::: :::::::::: ::: ::: ::::::::::

::: ::: ::::: ::: ::: ::::: :::: ::: :::: :::: :::: :::

::: ::: ::: ::: ::: :::::::: :::: :::::::: ::::

::: ::: ::: :: ::: :::::::::: :::::::::: :::: ::::::::::

::: ::: ::: :::::: ::: :::: ::: :::: :::

:::::::::: ::: ::: :::: ::: :::: :::......::: :::: :::......:::

......... ... ... ... ... .... .......... .... ..........

Linksys SmartSwitch SRW208 based on 88E6218 with ARM946E-S.

32MByte SDRAM. I-Cache 8 KB. D-Cache 8 KB. Cache Enabled.

Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.

Preparing to decompress...

100%

Decompressing SW from flash

100%

Running from RAM...

******************************************************************

*** Running SW Ver. 1.0.4 Date 06-Sep-2007 Time 09:11:40 ***

******************************************************************

HW version is 00.03.00

Base Mac address is: 00:22:6b:c0:79:d1

Dram size is : 32M bytes

Dram first block size is : 17152K bytes

Dram first PTR is : 0xF40000

Flash size is: 8M

01-Jan-2000 01:01:05 %CDB-I-LOADCONFIG: Loading startup configuration.

Device configuration:

PCB revision: 1

Slot 1 - SRW2008MP HW Rev. 0.1

Tapi Version: v1.3.3.1

Core Version: v1.3.3.1

01-Jan-2000 01:01:19 %INIT-I-InitCompleted: Initialization task is completed

============

User Name:

Password:

Hardware info

                                Versions
                                ========

  Boot Version:          1.0.1 (Date:  06-Jun-2006, Time:  17:23:21)

  Software Version:      1.0.4 (Date:  06-Sep-2007, Time:  09:11:40)

  Hardware Version:      00.03.00


                          General System Information
                          ==========================

  System Description:    SRW2008MP - 6-port Gigabit Switch with 2 Combo ports,

  System Up Time:        0,00:05:20 (days,hour:min:sec)

  System MAC Address:    00:22:6b:c0:79:d1

  System Contact:

  System Name:

  System Location:

Versions

========

Boot Version: 1.0.1 (Date: 06-Jun-2006, Time: 17:23:21)

Software Version: 1.0.4 (Date: 06-Sep-2007, Time: 09:11:40)

Hardware Version: 00.03.00

General System Information

==========================

System Description: SRW2008MP - 6-port Gigabit Switch with 2 Combo ports,

System Up Time: 0,00:05:20 (days,hour:min:sec)

System MAC Address: 00:22:6b:c0:79:d1

System Contact:

System Name:

System Location:

Linksys SRW2008x (managed switch) – Firmware

Door Sebastiaan Geplaatst op 2016-05-31 Geplaatst in Linksys Getagd met Firmware, Linksys, ls_srw2008-102.ros, ls_srw2008-104.ros, Managed switch, Router, SRW2008x, switch, UART

Linksys SRW2008x (managed switch) De firmware is te updaten via de webinterface: Voltooid

SRW2008/SRW2008P/SRW2008MP Firmware Release Note
Software version 1.0.4 09/11/2007
Boot version 1.0.1 06/13/2006
==========
1. Support of 100SFP
This release introduces an enhancement to support 100SFP module. The device can
automatically set up proper port setting for supported 100SFP modules: Linksys
MFELX1 and MFEFX1.
.
2. CPU Utilization Display
The application provides the ability to enable and disable the CPU utilization
mechanism and display its output. This application is controlled by WEB base
management to display the system CPU utilization. The display will be graphic,
showing history point per second over the user-selected period. If Java Virtual
Machine (JVM) is not installed on the client PC, the graph is not displayed.
Refer the link of http://www.java.com for JVM installation.
3. Power allocation per Port – SRW2008P,SRW2008MP
With this software release an enhancement to the PoE standard is introduced,
whereby the user configures the allocated power. If a Power Device (PD) on a PoE
port consumes more power than the specified allocate power, the port will be
shut down. If the user does not configure the power allocation, the PoE
classification is kept.
4. Total PoE Power set the max capacity- SRW2008P
Starting this release, one can upgrade the SRW2008P to support full power
allocation for all eight ports. After connecting the power supply of
SRW2008MP/SRW208MP, the user can use the web interface of Port Management--> PoE
Power setting to select “Extended” on the Power Supply Type drop-down menu.
Known Issues
=========
1. ACL --> MAC Based ACL
Creating a MAC ACL with to permit ethertype 0800 causes all traffic to be
forwarded. Configuring a MAC ACL to permit ethertype 86DD causes all traffic to
be denied.
Recommended Workaround: To avoid these situations, add a rule to deny any any.
2 . Setup --> network setting
Changing any field on the Network Settings Tab will result in sending a DHCP
release and than Discover which may lead to in IP address change.
3. Admin --> Cable Test
When testing cable with advanced test only (without simple test before), the
results are incorrect.
4. Admin --> Port Mirroring
After configuring port monitoring, the target port is grayed out, and cannot be
modified.
Recommended Workaround: Delete the mirroring session, and reconfigure.
5. QoS --> Basic Mode (Double Check this Bug) 
The "Trust Mode Table" is not functional. Attempting to disable the trust mode
on an interface of the trust mode table results in an error message, and does
not disable the trust mode on a per port basis.
6. QoS --> Advanced Mode
(a) Newly created entries in the Advanced Mode are displayed in the table only
after refreshing the table. For example, after creating a new policy, using the
pop-up window, it is displayed only after refreshing the main window.
(b) Under one policy, one can only select either Single or Aggregate police type
but not both.
(c) It is not possible to create two identical policers with the same settings
and action.
(d) QoS advanced mode page will refresh twice if browsed to it.
7. Security --> TACACS+
It is impossible to update the key string, after a server has already been
configured.
Recommended Workaround: To update the key string, the server must be deleted,
and then re-configured.
8. Setup --> Time
(a) The DST dates cannot be edited after selecting different radio boxes.
Recommended Workaround: Refresh the page, and configure.
(b) Configuring Daylight Savings Time in conjunction with SNTP servers may
result in unclear errors.
(c) The prioritization between servers is not maintained when two servers are
configured simultaneously.
(d) If a lower IP address is added after the first one was configured and saved,
then the two IP addresses swap location and prioritization.
9. SNMP --> Communities
 To edit fields including the change of SNMP mode, the entry needs to be
deleted, and then re-entered.
10. SNMP --> Group Membership
It is not possible to modify the user name after it has been entered.
Recommended Workaround: Delete the user and reconfigure.
11. Image Download
When downloading via tftp or http, performing Power off/on to the device may
result in requirement for downloading the image via XMODEM after the device
recovers. When downloading via XModem, the device recovers by itself.
Note: Avoid disconnecting the device from a power source during image upload
12. Timestamps
The order of the month and day in the dates presented in syslog messages is the
European fromat (dd/mm/yy), and not the US format.
13. Security--> Storm Control (Need to double check)
Configuring Unknown Unicast mode results in an error message.
14. Web browser availability
The web management interface is best viewed using Internet Explorer 5.5 and up,
with a resolution of 1024 x 768. In the current software version, certain pages
cannot be viewed well using other browsers. It is recommended to apply the
following workarounds. 
Note: Internet Explorer web browser must be installed prior to running the
following procedures.
-Using Mozilla Firefox Web Browser:
(a) Install Firefox "IE Tab" add-ons. The latest version is available on
https://addons.mozilla.org/firefox/1419/
(b) Select Tools --> IE Tab. Add in the IP address of switches to Sites Fitters
 (e.g. “http://172.18.1.27” accepts wildcard http://172.18.1.*).
(c) Ensure that cookies are enabled, by clicking "enable" to "All sites to set
cookies"Tools -> Options -> Privacy -> Cookies.
-Using Netscape Web Browser: Click the icon in the left corner, and select "IE
Display".
15. Management --> Password
User can not change the default password from the web UI
Recommended Workaround: Use the console menu
16. VLAN Management --> VLAN to Port
When VLAN to Port is set the action is performed successfully and then an error
message is displayed on the window.
Recommended Workaround: Ignore error message

100

101

102

103

104

105

106

107

108

109

110

SRW2008/SRW2008P/SRW2008MP Firmware Release Note

Software version 1.0.4 09/11/2007

Boot version 1.0.1 06/13/2006

==========

1. Support of 100SFP

This release introduces an enhancement to support 100SFP module. The device can

automatically set up proper port setting for supported 100SFP modules: Linksys

MFELX1 and MFEFX1.

2. CPU Utilization Display

The application provides the ability to enable and disable the CPU utilization

mechanism and display its output. This application is controlled by WEB base

management to display the system CPU utilization. The display will be graphic,

showing history point per second over the user-selected period. If Java Virtual

Machine (JVM) is not installed on the client PC, the graph is not displayed.

Refer the link of http://www.java.com for JVM installation.

3. Power allocation per Port – SRW2008P,SRW2008MP

With this software release an enhancement to the PoE standard is introduced,

whereby the user configures the allocated power. If a Power Device (PD) on a PoE

port consumes more power than the specified allocate power, the port will be

shut down. If the user does not configure the power allocation, the PoE

classification is kept.

4. Total PoE Power set the max capacity- SRW2008P

Starting this release, one can upgrade the SRW2008P to support full power

allocation for all eight ports. After connecting the power supply of

SRW2008MP/SRW208MP, the user can use the web interface of Port Management--> PoE

Power setting to select “Extended” on the Power Supply Type drop-down menu.

Known Issues

=========

1. ACL --> MAC Based ACL

Creating a MAC ACL with to permit ethertype 0800 causes all traffic to be

forwarded. Configuring a MAC ACL to permit ethertype 86DD causes all traffic to

be denied.

Recommended Workaround: To avoid these situations, add a rule to deny any any.

2 . Setup --> network setting

Changing any field on the Network Settings Tab will result in sending a DHCP

release and than Discover which may lead to in IP address change.

3. Admin --> Cable Test

When testing cable with advanced test only (without simple test before), the

results are incorrect.

4. Admin --> Port Mirroring

After configuring port monitoring, the target port is grayed out, and cannot be

modified.

Recommended Workaround: Delete the mirroring session, and reconfigure.

5. QoS --> Basic Mode (Double Check this Bug)

The "Trust Mode Table" is not functional. Attempting to disable the trust mode

on an interface of the trust mode table results in an error message, and does

not disable the trust mode on a per port basis.

6. QoS --> Advanced Mode

(a) Newly created entries in the Advanced Mode are displayed in the table only

after refreshing the table. For example, after creating a new policy, using the

pop-up window, it is displayed only after refreshing the main window.

(b) Under one policy, one can only select either Single or Aggregate police type

but not both.

and action.

(d) QoS advanced mode page will refresh twice if browsed to it.

7. Security --> TACACS+

It is impossible to update the key string, after a server has already been

configured.

Recommended Workaround: To update the key string, the server must be deleted,

and then re-configured.

8. Setup --> Time

(a) The DST dates cannot be edited after selecting different radio boxes.

Recommended Workaround: Refresh the page, and configure.

(b) Configuring Daylight Savings Time in conjunction with SNTP servers may

result in unclear errors.

configured simultaneously.

(d) If a lower IP address is added after the first one was configured and saved,

then the two IP addresses swap location and prioritization.

9. SNMP --> Communities

To edit fields including the change of SNMP mode, the entry needs to be

deleted, and then re-entered.

10. SNMP --> Group Membership

It is not possible to modify the user name after it has been entered.

Recommended Workaround: Delete the user and reconfigure.

11. Image Download

When downloading via tftp or http, performing Power off/on to the device may

result in requirement for downloading the image via XMODEM after the device

recovers. When downloading via XModem, the device recovers by itself.

Note: Avoid disconnecting the device from a power source during image upload

12. Timestamps

The order of the month and day in the dates presented in syslog messages is the

European fromat (dd/mm/yy), and not the US format.

13. Security--> Storm Control (Need to double check)

Configuring Unknown Unicast mode results in an error message.

14. Web browser availability

The web management interface is best viewed using Internet Explorer 5.5 and up,

with a resolution of 1024 x 768. In the current software version, certain pages

cannot be viewed well using other browsers. It is recommended to apply the

following workarounds.

Note: Internet Explorer web browser must be installed prior to running the

following procedures.

-Using Mozilla Firefox Web Browser:

(a) Install Firefox "IE Tab" add-ons. The latest version is available on

https://addons.mozilla.org/firefox/1419/

(b) Select Tools --> IE Tab. Add in the IP address of switches to Sites Fitters

(e.g. “http://172.18.1.27” accepts wildcard http://172.18.1.*).

cookies"Tools -> Options -> Privacy -> Cookies.

-Using Netscape Web Browser: Click the icon in the left corner, and select "IE

Display".

15. Management --> Password

User can not change the default password from the web UI

Recommended Workaround: Use the console menu

16. VLAN Management --> VLAN to Port

When VLAN to Port is set the action is performed successfully and then an error

message is displayed on the window.

Recommended Workaround: Ignore error message

Download firmware 1.04 @ software.cisco.com Download firmware 1.02 @ www.drewy.com Download PDF release notes @ cisco.com [#/firmware/linksys_swr2008x” ]

Prusa i3 Geeetech – Firmware (Sanguinololu)

Door Sebastiaan Geplaatst op 2016-04-19 Geplaatst in 3D Printer - Prusa i3 Getagd met 3D printer, Firmware, Geeetech, Marlin, prusa i3, Sanguinololu

Let op: Het werkt niet om de nieuwste ArduinoIDE + Sanguino Board + Marlin firmware te gebruiken, Geeetech heeft een “eigen” editie gemaakt! Informatie (ENG) Board Sanguinololu: How to install the firmware for Sanguinololu 1. Download Arduino1.0.1 on your PC. …

Prusa i3 Geeetech – Firmware (Sanguinololu) Lees meer »

Prusa i3 Geeetech – Firmware (RAMPS 1.4 / GT2560)

Door Sebastiaan Geplaatst op 2016-04-19 Geplaatst in 3D Printer - Prusa i3 Getagd met 3D printer, Firmware, Geeetech, GT2560, Marlin, prusa i3, RAMPS 1.4

Informatie (ENG) Board GT2560: Board RAMPS 1.4: How to install the firmware for RAMPS1.4 / GT2560 1. Install Arduino1.0.1 on your PC. Download arduino1.0.1 here 2. Connect the printer to the PC with your USB cable. 3. Unzip the firmware. …

Prusa i3 Geeetech – Firmware (RAMPS 1.4 / GT2560) Lees meer »

Linksys WAG354G (ADSL router) – Firmware (OpenWRT)

Door Sebastiaan Geplaatst op 2016-04-08 Geplaatst in Linksys Getagd met ADSL, Firmware, Linksys, Openwrt, Router, UART, WAG354G, Wireless, WLAN

Linksys WAG354G v1/v2 (ADSL router) OpenWRT (MARCO V.) KAMIKAZE (bleeding edge, r10074) (2008-01-01) Bronnen: webalice.it cyberstorm.altervista.org Lately I have attempted to build OpenWrt for the AR7 platform.Building process was straight-forward, after selecting your target (AR7) and desired packages with “make …

Linksys WAG354G (ADSL router) – Firmware (OpenWRT) Lees meer »

Linksys WAG354G (ADSL router) – Firmware

Door Sebastiaan Geplaatst op 2016-04-08 Geplaatst in Linksys Getagd met ADSL, Firmware, Linksys, Router, UART, WAG354G, Wireless, WLAN

Linksys WAG354G v1/v2 (ADSL router) De firmware is te updaten via de webinterface:

Firmware Version 1.01.11
- Removed the MIB OID â€œ1.3.6.1.2.1.25.4.2.1.5â€ to avoid PPPoE password disclosure
- Fixed UI bug: ARP table showed "ART/RARP" title in English language pack
- Fixed bug: additional PPPoE Connect on Demand button did not function
- Fixed bug: Status page showed "undefined" in time/date field
- Fixed bug: PPPoE user name and password was revealed through MIB Browser

Firmware Version 1.01.05
- Fixed and updated help pages and other problems with web GUI
- Fixed problem with LAN receiving WAN PADI packet
- Fixed problems with SNMP 
- Fixed problems with Management password set to blank
- Fixed problems with QoS input values
- Fixed problems with VPN under Manual mode
- Fixed problems with MTU not accepting some values in manual mode
- Fixed problems with different messages showing when PPP disconnected for
PPPoA and PPPoE
- Fixed problems with selecting some time zones

Firmware Version 1.01.03
- Initial release

-------------------------------------------------------------------------
Linksys, A division of Cisco Systems, Inc.


Produkt/Product: WAG354G Annex B (Hardware Version 1)

Einteilung/Classification: Firmware-Versionshistorie/
Firmware Release History

Versionsdatum/Release Date: 25, Oct. 2006

Firmware-Version: 1.01.11 (ETSI)
____________________________________________________________

1.01.11
- Removed the MIB OID â€œ1.3.6.1.2.1.25.4.2.1.5â€ to avoid PPPoE password disclosure
- Fixed UI bug: ARP table showed "ART/RARP" title in English language pack
- Fixed bug: additional PPPoE Connect on Demand button did not function
- Fixed bug: Status page showed "undefined" in time/date field
- Fixed bug: PPPoE user name and password was revealed through MIB Browser

1.01.09
- ADSL2+ Upgrade

1.01.05
- Updated help pages and web GUI

1.01.03
- Initial Release

General Notes: 
- This firmware is only for usage with WAG354G Annex B hardware version 1 units.

Firmware Version 1.01.11

- Removed the MIB OID â€œ1.3.6.1.2.1.25.4.2.1.5â€ to avoid PPPoE password disclosure

- Fixed UI bug: ARP table showed "ART/RARP" title in English language pack

- Fixed bug: additional PPPoE Connect on Demand button did not function

- Fixed bug: Status page showed "undefined" in time/date field

- Fixed bug: PPPoE user name and password was revealed through MIB Browser

Firmware Version 1.01.05

- Fixed and updated help pages and other problems with web GUI

- Fixed problem with LAN receiving WAN PADI packet

- Fixed problems with SNMP

- Fixed problems with Management password set to blank

- Fixed problems with QoS input values

- Fixed problems with VPN under Manual mode

- Fixed problems with MTU not accepting some values in manual mode

- Fixed problems with different messages showing when PPP disconnected for

PPPoA and PPPoE

- Fixed problems with selecting some time zones

Firmware Version 1.01.03

- Initial release

-------------------------------------------------------------------------

Linksys, A division of Cisco Systems, Inc.

Produkt/Product: WAG354G Annex B (Hardware Version 1)

Einteilung/Classification: Firmware-Versionshistorie/

Firmware Release History

Versionsdatum/Release Date: 25, Oct. 2006

Firmware-Version: 1.01.11 (ETSI)

____________________________________________________________

1.01.11

- Removed the MIB OID â€œ1.3.6.1.2.1.25.4.2.1.5â€ to avoid PPPoE password disclosure

- Fixed UI bug: ARP table showed "ART/RARP" title in English language pack

- Fixed bug: additional PPPoE Connect on Demand button did not function

- Fixed bug: Status page showed "undefined" in time/date field

- Fixed bug: PPPoE user name and password was revealed through MIB Browser

1.01.09

- ADSL2+ Upgrade

1.01.05

- Updated help pages and web GUI

1.01.03

- Initial Release

General Notes:

- This firmware is only for usage with WAG354G Annex B hardware version 1 units.

[#/firmware/linksys_wag354g” ]

Linksys WAG354G (ADSL router) – Bootlog via UART

Door Sebastiaan Geplaatst op 2016-04-08 Geplaatst in Linksys Getagd met ADSL, Bootlog, Firmware, Linksys, Router, UART, WAG354G, WLAN

Linksys WAG354G v1/v2 (ADSL router) Bootlog via UART Dit is de OEM bootlog bij het opstarten via de UART seriele verbinding op de printplaat.

free space start: 0xb0020000
free space end: 0xb0400000

Minimal POST completed...     Success.
Last reset cause: Software reset (memory controller also reset)

PSPBoot1.2 rev: 0.22.17
(c) Copyright 2002-2004 Texas Instruments, Inc. All Rights Reserved.
FlashType:

No mac find, use default mac
mac_value: 00:16:B6:01:B9:D8

Press ESC for monitor... 521

(psbl) 
boot order: f
boot file: mtd1

Booting...
Launching kernel decompressor.
Starting LZMA Uncompression Algorithm.
Copyright (C) 2003 Texas Instruments Incorporated; Copyright (C) 1999-2003 Igor Pavlov.
Compressed file is LZMA format.
Kernel decompressor was successful ... launching kernel.

LIN
X 
tarted..ConfThiCPU revision is: 00018448
Primary instruction cache 16kb, linesize 16 bytes (4 ways)
Primary data cache 16kb, linesize 16 bytes (4 ways)
Number of TLB entries 16.
Linux version 2.4.17_mvl21-malta-mips_fp_le (root@59-120-187-167.hinet-ip.hinet.net) (gcc version 2.95.3 20010315 (release/MontaVista)) #31 €» 10€ë 28 00:23:15 CST 2006
Determined physical RAM map:
 memory: 14000000 @ 00000000 (reserved)
 memory: 00020000 @ 14000000 (ROM data)
 memory: 00fe0000 @ 14020000 (usable)
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
.........boot_code Pspboot...........
..54....49....45....4e....56....30....2e....38....00....ff..
base address: b0010000
env size: 65536
ptr: b0010000
Kernel command line: 
calculating r4koff... 000b71b0(750000)
CPU frequency 150.00 MHz
Calibrating delay loop... 149.91 BogoMIPS
Freeing Adam2 reserved memory [0x14001000,0x0001f000]
Memory: 13876k/16384k available (1888k kernel code, 2508k reserved, 139k data, 64k init)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
Checking for 'wait' instruction...  unavailable.
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
TI Optimizations: Allocating TI-Cached Memory Pool.
Warning: Number of buffers is not configured.Setting default to 512
Using 512 Buffers for TI-Cached Memory Pool.
DEBUG: Using Hybrid Mode.
NSP Optimizations: Succesfully allocated TI-Cached Memory Pool.
Initializing RT netlink socket
Starting kswapd
Disabling the Out Of Memory Killer
devfs: v1.7 (20011216) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
pty: 32 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with no serial options enabled
ttyS00 at 0xa8610e00 (irq = 15) is a 16550A
ttyS01 at 0xa8610f00 (irq = 16) is a 16550A
Vlynq CONFIG_MIPS_AVALANCHE_VLYNQ_PORTS=2
Vlynq Device vlynq0 registered with minor no 63 as misc device. Result=0
Vlynq instance:0 Link UP
Vlynq Device vlynq1 registered with minor no 62 as misc device. Result=0
VLYNQ 1 : init failed
block: 64 slots per queue, batch=16
Using the MAC with external PHY
Cpmac driver is allocating buffer memory at init time.
Using the MAC with external PHY
Cpmac driver Disable TX complete interrupt setting threshold to 20.
Default Asymmetric MTU for eth0 1500
PPP generic driver version 2.4.1
avalanche flash device: 0x400000 at 0x10000000.
 Amd/Fujitsu Extended Query Table v1.1 at 0x0040
Physically mapped flash: Swapping erase regions for broken CFI table.
number of CFI chips: 1
Looking for mtd device :mtd0:
Found a mtd0 image (0xe0000), with size (0x2f0000).
Looking for mtd device :mtd1:
Found a mtd1 image (0x20000), with size (0x3b0000).
Looking for mtd device :mtd2:
Found a mtd2 image (0x0), with size (0x20000).
Looking for mtd device :mtd3:
Found a mtd3 image (0x3f0000), with size (0x10000).
Looking for mtd device :mtd4:
Found a mtd4 image (0x3d0000), with size (0x20000).
Creating 5 MTD partitions on "Physically mapped flash":
0x000e0000-0x003d0000 : "mtd0"
0x00020000-0x003d0000 : "mtd1"
0x00000000-0x00020000 : "mtd2"
0x003f0000-0x00400000 : "mtd3"
0x003d0000-0x003f0000 : "mtd4"
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 1024)
IPv4 over IPv4 tunneling driver
Default Asymmetric MTU for tunl0 1480
GRE over IPv4 tunneling driver
Default Asymmetric MTU for gre0 1476
Linux IP multicast router 0.06 plus PIM-SM
klips_info:ipsec_init: KLIPS startup, FreeS/WAN IPSec version: super-freeswan-1.99.8
Default Asymmetric MTU for ipsec0 0
Default Asymmetric MTU for ipsec1 0
Default Asymmetric MTU for ipsec2 0
Default Asymmetric MTU for ipsec3 0
Default Asymmetric MTU for ipsec4 0
klips_info:ipsec_alg_init: KLIPS alg v=0.8.1-0 (EALG_MAX=255, AALG_MAX=15)
klips_info:ipsec_alg_init: calling ipsec_alg_static_init()
ipsec_1des_init(alg_type=15 alg_id=2 name=1des): ret=0
You should NOT load 1DES support except for testing purposes !
ipsec_null_init(alg_type=15 alg_id=11 name=null): ret=0
ip_conntrack version 2.0 (128 buckets, 1024 max) - 392 bytes per conntrack
ip_tables: (c)2000 Netfilter core team
netfilter PSD loaded - (c) astaro AG
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
Initializing the WAN Bridge.
Please set the MAC Address for the WAN Bridge.
Set the Environment variable 'wan_br_mac'. 
MAC Address should be in the following format: xx.xx.xx.xx.xx.xx
802.1Q VLAN Support v1.6  Ben Greear <greearb@candelatech.com>
vlan Initialization complete.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 64k freed
Firmware Version: 1.01.11
SQUASHFS error: Can't find a SQUASHFS superblock on mtdblock(31,4)
ret = -1
www -> /www
mount: Invalid argument
Hit enter to continue...killall: httpd: no process killed

 Configured 19 states 
now insmod tiatm
Using /lib/modules/2.4.17_mvl21-malta-mips_fp_le/kernel/drivers/atm/tiatm.o
name=[eth0] lan_ifname=[br0]
=====> set br0 hwaddr to eth0
wlconf: No such file or directory
Lan Ipaddr: 255.255.255.0 Netmask: 255.255.255.0................
255.255.255.0 255.255.255.0
mixed mode
insmod ap driver
Using /lib/modules/2.4.17_mvl21-malta-mips_fp_le/kernel/drivers/net/tiap.o
ret = 0
.............list  ..............
antsel.c: External Antenna
[HTTPD Starting on /www]
The boot is UNKNOWN
tftp server started
tftpd: standalone socket
HTTPD start,  port 80
dhcpd:auto_search_ip=0,firstsetlanip=1
.............list  ..............
info, udhcp server (v0.9.8) started
QE: No such file or directory
log_ipaddr=255
killall: leijun--upnpd-igd ver 0.83 2004-0329: no process killed
Now Start syslog.........................!!zebra disabled
killall: adslpolling: no process killed
IDLE
Hit enter to continue...wan def hwaddr 00:16:B6:01:B9:D9
polling now .......
upnpd-igd:current select wan connection:0
upnp_content_num_0 = 14
killall: begin_now: no process killed
Hit enter to continue...Hit enter to continue...

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

147

148

149

150

151

152

153

154

155

156

157

158

159

160

161

162

163

164

165

166

167

168

169

170

171

172

173

174

175

176

177

178

179

180

181

182

free space start: 0xb0020000

free space end: 0xb0400000

Minimal POST completed... Success.

Last reset cause: Software reset (memory controller also reset)

PSPBoot1.2 rev: 0.22.17

FlashType:

No mac find, use default mac

mac_value: 00:16:B6:01:B9:D8

Press ESC for monitor... 521

(psbl)

boot order: f

boot file: mtd1

Booting...

Launching kernel decompressor.

Starting LZMA Uncompression Algorithm.

Compressed file is LZMA format.

Kernel decompressor was successful ... launching kernel.

LIN

tarted..ConfThiCPU revision is: 00018448

Primary instruction cache 16kb, linesize 16 bytes (4 ways)

Primary data cache 16kb, linesize 16 bytes (4 ways)

Number of TLB entries 16.

Linux version 2.4.17_mvl21-malta-mips_fp_le (root@59-120-187-167.hinet-ip.hinet.net) (gcc version 2.95.3 20010315 (release/MontaVista)) #31 €» 10€ë 28 00:23:15 CST 2006

Determined physical RAM map:

memory: 14000000 @ 00000000 (reserved)

memory: 00020000 @ 14000000 (ROM data)

memory: 00fe0000 @ 14020000 (usable)

On node 0 totalpages: 4096

zone(0): 4096 pages.

zone(1): 0 pages.

zone(2): 0 pages.

.........boot_code Pspboot...........

..54....49....45....4e....56....30....2e....38....00....ff..

base address: b0010000

env size: 65536

ptr: b0010000

Kernel command line:

calculating r4koff... 000b71b0(750000)

CPU frequency 150.00 MHz

Calibrating delay loop... 149.91 BogoMIPS

Freeing Adam2 reserved memory [0x14001000,0x0001f000]

Memory: 13876k/16384k available (1888k kernel code, 2508k reserved, 139k data, 64k init)

Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)

Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)

Mount-cache hash table entries: 512 (order: 0, 4096 bytes)

Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)

Page-cache hash table entries: 4096 (order: 2, 16384 bytes)

Checking for 'wait' instruction... unavailable.

POSIX conformance testing by UNIFIX

Linux NET4.0 for Linux 2.4

Based upon Swansea University Computer Society NET3.039

TI Optimizations: Allocating TI-Cached Memory Pool.

Warning: Number of buffers is not configured.Setting default to 512

Using 512 Buffers for TI-Cached Memory Pool.

DEBUG: Using Hybrid Mode.

NSP Optimizations: Succesfully allocated TI-Cached Memory Pool.

Initializing RT netlink socket

Starting kswapd

Disabling the Out Of Memory Killer

devfs: v1.7 (20011216) Richard Gooch (rgooch@atnf.csiro.au)

devfs: boot_options: 0x1

pty: 32 Unix98 ptys configured

Serial driver version 5.05c (2001-07-08) with no serial options enabled

ttyS00 at 0xa8610e00 (irq = 15) is a 16550A

ttyS01 at 0xa8610f00 (irq = 16) is a 16550A

Vlynq CONFIG_MIPS_AVALANCHE_VLYNQ_PORTS=2

Vlynq Device vlynq0 registered with minor no 63 as misc device. Result=0

Vlynq instance:0 Link UP

Vlynq Device vlynq1 registered with minor no 62 as misc device. Result=0

VLYNQ 1 : init failed

block: 64 slots per queue, batch=16

Using the MAC with external PHY

Cpmac driver is allocating buffer memory at init time.

Using the MAC with external PHY

Cpmac driver Disable TX complete interrupt setting threshold to 20.

Default Asymmetric MTU for eth0 1500

PPP generic driver version 2.4.1

avalanche flash device: 0x400000 at 0x10000000.

Amd/Fujitsu Extended Query Table v1.1 at 0x0040

Physically mapped flash: Swapping erase regions for broken CFI table.

number of CFI chips: 1

Looking for mtd device :mtd0:

Found a mtd0 image (0xe0000), with size (0x2f0000).

Looking for mtd device :mtd1:

Found a mtd1 image (0x20000), with size (0x3b0000).

Looking for mtd device :mtd2:

Found a mtd2 image (0x0), with size (0x20000).

Looking for mtd device :mtd3:

Found a mtd3 image (0x3f0000), with size (0x10000).

Looking for mtd device :mtd4:

Found a mtd4 image (0x3d0000), with size (0x20000).

Creating 5 MTD partitions on "Physically mapped flash":

0x000e0000-0x003d0000 : "mtd0"

0x00020000-0x003d0000 : "mtd1"

0x00000000-0x00020000 : "mtd2"

0x003f0000-0x00400000 : "mtd3"

0x003d0000-0x003f0000 : "mtd4"

NET4: Linux TCP/IP 1.0 for NET4.0

IP Protocols: ICMP, UDP, TCP, IGMP

IP: routing cache hash table of 512 buckets, 4Kbytes

TCP: Hash tables configured (established 1024 bind 1024)

IPv4 over IPv4 tunneling driver

Default Asymmetric MTU for tunl0 1480

GRE over IPv4 tunneling driver

Default Asymmetric MTU for gre0 1476

Linux IP multicast router 0.06 plus PIM-SM

klips_info:ipsec_init: KLIPS startup, FreeS/WAN IPSec version: super-freeswan-1.99.8

Default Asymmetric MTU for ipsec0 0

Default Asymmetric MTU for ipsec1 0

Default Asymmetric MTU for ipsec2 0

Default Asymmetric MTU for ipsec3 0

Default Asymmetric MTU for ipsec4 0

klips_info:ipsec_alg_init: KLIPS alg v=0.8.1-0 (EALG_MAX=255, AALG_MAX=15)

klips_info:ipsec_alg_init: calling ipsec_alg_static_init()

ipsec_1des_init(alg_type=15 alg_id=2 name=1des): ret=0

You should NOT load 1DES support except for testing purposes !

ipsec_null_init(alg_type=15 alg_id=11 name=null): ret=0

ip_conntrack version 2.0 (128 buckets, 1024 max) - 392 bytes per conntrack

netfilter PSD loaded - (c) astaro AG

NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.

NET4: Ethernet Bridge 008 for NET4.0

Initializing the WAN Bridge.

Please set the MAC Address for the WAN Bridge.

Set the Environment variable 'wan_br_mac'.

MAC Address should be in the following format: xx.xx.xx.xx.xx.xx

802.1Q VLAN Support v1.6 Ben Greear <greearb@candelatech.com>

vlan Initialization complete.

VFS: Mounted root (squashfs filesystem) readonly.

Mounted devfs on /dev

Freeing unused kernel memory: 64k freed

Firmware Version: 1.01.11

SQUASHFS error: Can't find a SQUASHFS superblock on mtdblock(31,4)

ret = -1

www -> /www

mount: Invalid argument

Hit enter to continue...killall: httpd: no process killed

Configured 19 states

now insmod tiatm

Using /lib/modules/2.4.17_mvl21-malta-mips_fp_le/kernel/drivers/atm/tiatm.o

name=[eth0] lan_ifname=[br0]

=====> set br0 hwaddr to eth0

wlconf: No such file or directory

Lan Ipaddr: 255.255.255.0 Netmask: 255.255.255.0................

255.255.255.0 255.255.255.0

mixed mode

insmod ap driver

Using /lib/modules/2.4.17_mvl21-malta-mips_fp_le/kernel/drivers/net/tiap.o

ret = 0

.............list ..............

antsel.c: External Antenna

[HTTPD Starting on /www]

The boot is UNKNOWN

tftp server started

tftpd: standalone socket

HTTPD start, port 80

dhcpd:auto_search_ip=0,firstsetlanip=1

.............list ..............

info, udhcp server (v0.9.8) started

QE: No such file or directory

log_ipaddr=255

killall: leijun--upnpd-igd ver 0.83 2004-0329: no process killed

Now Start syslog.........................!!zebra disabled

killall: adslpolling: no process killed

IDLE

Hit enter to continue...wan def hwaddr 00:16:B6:01:B9:D9

polling now .......

upnpd-igd:current select wan connection:0

upnp_content_num_0 = 14

killall: begin_now: no process killed

Hit enter to continue...Hit enter to continue...

Bij het indrukken van de miniswitch (voor interne/externe antenne), worden deze berichten getoond:

antsel.c: Internal Antenna
antsel.c: External Antenna

1 2	antsel.c: Internal Antenna antsel.c: External Antenna

UART …

Linksys WAG354G (ADSL router) – Bootlog via UART Lees meer »

Linux Firmware drivers (non-free)

Door Sebastiaan Geplaatst op 2016-02-17 Geplaatst in Stuurprogramma's Getagd met driver, Firmware, Linux, NON-FREE, Realtek

Non-free firmware for Linux kernel drivers This package provides non-free firmware used by Linux kernel drivers. Most of the firmware in this package is for television tuner cards. However, non-free firmware for other classes of devices are provided as well. …

Linux Firmware drivers (non-free) Lees meer »

Firmware bouwen – U-boot (Lantiq Danube)

Door Sebastiaan Geplaatst op 2016-01-14 Geplaatst in BIOS / Firmware software Getagd met Danube, Firmware, GIT, Lantiq, Linux, Openwrt, U-boot

Website Informatie (ENG) OpenWRT based repository created to compile u-boot for Lantiq Danube boards This repository is only intended to build u-boot images for some Lantiq Danube based boards: easy50712 easy50812 arv4518PW arv4520PW arv4525PW arv452CPW arv7518PW arv752DPW arv752DPW22 The features included …

Firmware bouwen – U-boot (Lantiq Danube) Lees meer »

Zoeken

Tag: Firmware