bibliotheek Archieven - DomoticX Knowledge Center

Tag: bibliotheek

Python Library – pymodbusTCP

by SebastiaanPosted on 2018-02-24 Geplaatst in Modbus Software, Python libraries

Python pymodbusTCP Voor communicatie van Modbus TCP/IP Niet voor Modbus RTU Modbus ASCII Modbus RTU over TCP Installatie:

sudo apt-get update
sudo apt-get install -y python-dev python-pip
sudo pip install -U pymodbusTCP

sudo apt-get update

sudo apt-get install -y python-dev python-pip

sudo pip install -U pymodbusTCP

Installatie voor Python 3:

sudo apt-get update
sudo apt-get install -y python3 python3-dev python-pip
sudo pip3 install -U pymodbusTCP

sudo apt-get update

sudo apt-get install -y python3 python3-dev python-pip

sudo pip3 install -U pymodbusTCP

Mijn voorbeeld:

#!/usr/bin/env python
from pyModbusTCP.client import ModbusClient

client = ModbusClient(host="192.168.0.0", port=502, auto_open=True, auto_close=True, timeout=10)
data = client.read_holding_registers(0, 1)    # FUNCTIE 03 - Lees register 0, 1 lang
print "Waarde register: ", data[0]
client.close()

#!/usr/bin/env python

from pyModbusTCP.client import ModbusClient

client = ModbusClient(host="192.168.0.0", port=502, auto_open=True, auto_close=True, timeout=10)

data = client.read_holding_registers(0, 1) # FUNCTIE 03 - Lees register 0, 1 lang

print "Waarde register: ", data[0]

client.close()

Informatie (ENG): Summary A simple Modbus/TCP library for Python A simple Modbus/TCP client …

Python Library – pymodbusTCP Read More »

Getagd met bibliotheek, programmeren, pymodbusTCP, Python

Arduino Library – CO2 sensor K30

by SebastiaanPosted on 2017-11-01 Geplaatst in Arduino libraries

Installatie van Arduino IDE libraries: Arduino info Informatie (ENG) K30 CO2 sensor module I2C Library This is an Arduino Library for K30 CO2 NDIR module from Senseair. The sensor module is connected to Arduino using I2C. The sensor module is powered …

Arduino Library – CO2 sensor K30 Read More »

Getagd met Arduino, bibliotheek, CO2, K40, Library, sensoren

Python Library – pymodbus

by SebastiaanPosted on 2017-10-13 Geplaatst in Modbus Software, Python libraries

Python pymodbus Voor communicatie van Modbus RTU Modbus ASCII Modbus RTU over TCP Niet voor Modbus TCP/IP Installatie:

sudo apt-get update
sudo apt-get install -y python-dev python-pip
sudo pip install -U pymodbus

sudo apt-get update

sudo apt-get install -y python-dev python-pip

sudo pip install -U pymodbus

Installatie voor Python 3:

sudo apt-get update
sudo apt-get install -y python3 python3-dev python-pip
sudo pip3 install -U pymodbus

sudo apt-get update

sudo apt-get install -y python3 python3-dev python-pip

sudo pip3 install -U pymodbus

Collecting pymodbus3
  Downloading https://www.piwheels.hostedpi.com/simple/pymodbus3/pymodbus3-1.0.0-py3-none-any.whl (76kB)
    100% |¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦| 81kB 1.5MB/s
Collecting pyserial>=2.6 (from pymodbus3)
  Using cached pyserial-3.4-py2.py3-none-any.whl
Collecting twisted>=12.2.0 (from pymodbus3)
  Downloading https://www.piwheels.hostedpi.com/simple/twisted/Twisted-17.9.0-cp35-cp35m-linux_armv7l.whl (3.0MB)
    100% |¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦| 3.0MB 98kB/s
Collecting incremental>=16.10.1 (from twisted>=12.2.0->pymodbus3)
  Downloading incremental-17.5.0-py2.py3-none-any.whl
Collecting constantly>=15.1 (from twisted>=12.2.0->pymodbus3)
  Downloading constantly-15.1.0-py2.py3-none-any.whl
Collecting hyperlink>=17.1.1 (from twisted>=12.2.0->pymodbus3)
  Downloading hyperlink-17.3.1-py2.py3-none-any.whl (73kB)
    100% |¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦| 81kB 2.0MB/s
Collecting zope.interface>=4.0.2 (from twisted>=12.2.0->pymodbus3)
  Downloading https://www.piwheels.hostedpi.com/simple/zope-interface/zope.interface-4.4.3-cp35-cp35m-linux_armv7l.whl (161kB)
    100% |¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦| 163kB 1.4MB/s
Collecting Automat>=0.3.0 (from twisted>=12.2.0->pymodbus3)
  Downloading Automat-0.6.0-py2.py3-none-any.whl
Collecting setuptools (from zope.interface>=4.0.2->twisted>=12.2.0->pymodbus3)
  Downloading setuptools-38.4.0-py2.py3-none-any.whl (489kB)
    100% |¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦| 491kB 549kB/s
Collecting six (from Automat>=0.3.0->twisted>=12.2.0->pymodbus3)
  Downloading six-1.11.0-py2.py3-none-any.whl
Collecting attrs (from Automat>=0.3.0->twisted>=12.2.0->pymodbus3)
  Downloading attrs-17.4.0-py2.py3-none-any.whl
Installing collected packages: pyserial, incremental, constantly, hyperlink, setuptools, zope.interface, six, attrs, Automat, twisted, pymodbus3
  Found existing installation: pyserial 3.2.1
    Not uninstalling pyserial at /usr/lib/python3/dist-packages, outside environment /usr
  Found existing installation: setuptools 33.1.1
    Not uninstalling setuptools at /usr/lib/python3/dist-packages, outside environment /usr
  Found existing installation: six 1.10.0
    Not uninstalling six at /usr/lib/python3/dist-packages, outside environment /usr
Successfully installed Automat-0.6.0 attrs-17.4.0 constantly-15.1.0 hyperlink-17.3.1 incremental-17.5.0 pymodbus3-1.0.0 pyserial-3.4 setuptools-38.4.0 six-1.11.0 twisted-17.9.0 zope.interface-4.4.3

Collecting pymodbus3

Downloading https://www.piwheels.hostedpi.com/simple/pymodbus3/pymodbus3-1.0.0-py3-none-any.whl (76kB)

100% |¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦| 81kB 1.5MB/s

Collecting pyserial>=2.6 (from pymodbus3)

Using cached pyserial-3.4-py2.py3-none-any.whl

Collecting twisted>=12.2.0 (from pymodbus3)

Downloading https://www.piwheels.hostedpi.com/simple/twisted/Twisted-17.9.0-cp35-cp35m-linux_armv7l.whl (3.0MB)

100% |¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦| 3.0MB 98kB/s

Collecting incremental>=16.10.1 (from twisted>=12.2.0->pymodbus3)

Downloading incremental-17.5.0-py2.py3-none-any.whl

Collecting constantly>=15.1 (from twisted>=12.2.0->pymodbus3)

Downloading constantly-15.1.0-py2.py3-none-any.whl

Collecting hyperlink>=17.1.1 (from twisted>=12.2.0->pymodbus3)

Downloading hyperlink-17.3.1-py2.py3-none-any.whl (73kB)

100% |¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦| 81kB 2.0MB/s

Collecting zope.interface>=4.0.2 (from twisted>=12.2.0->pymodbus3)

Downloading https://www.piwheels.hostedpi.com/simple/zope-interface/zope.interface-4.4.3-cp35-cp35m-linux_armv7l.whl (161kB)

100% |¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦| 163kB 1.4MB/s

Collecting Automat>=0.3.0 (from twisted>=12.2.0->pymodbus3)

Downloading Automat-0.6.0-py2.py3-none-any.whl

Collecting setuptools (from zope.interface>=4.0.2->twisted>=12.2.0->pymodbus3)

Downloading setuptools-38.4.0-py2.py3-none-any.whl (489kB)

100% |¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦| 491kB 549kB/s

Collecting six (from Automat>=0.3.0->twisted>=12.2.0->pymodbus3)

Downloading six-1.11.0-py2.py3-none-any.whl

Collecting attrs (from Automat>=0.3.0->twisted>=12.2.0->pymodbus3)

Downloading attrs-17.4.0-py2.py3-none-any.whl

Installing collected packages: pyserial, incremental, constantly, hyperlink, setuptools, zope.interface, six, attrs, Automat, twisted, pymodbus3

Found existing installation: pyserial 3.2.1

Not uninstalling pyserial at /usr/lib/python3/dist-packages, outside environment /usr

Found existing installation: setuptools 33.1.1

Not uninstalling setuptools at /usr/lib/python3/dist-packages, outside environment /usr

Found existing installation: six 1.10.0

Not uninstalling six at /usr/lib/python3/dist-packages, outside environment /usr

Successfully installed Automat-0.6.0 attrs-17.4.0 constantly-15.1.0 hyperlink-17.3.1 incremental-17.5.0 pymodbus3-1.0.0 pyserial-3.4 setuptools-38.4.0 six-1.11.0 twisted-17.9.0 zope.interface-4.4.3

Informatie (ENG): Summary Pymodbus is a full Modbus protocol implementation using twisted for its asynchronous …

Python Library – pymodbus Read More »

Getagd met bibliotheek, Library, programmeren, pymodbus, Python

Python Library – OLED display (luma.oled)

by SebastiaanPosted on 2017-09-27 Geplaatst in Python libraries

Python OLED library (luma.oled) Informatie (ENG): Display drivers for SSD1306 / SSD1322 / SSD1325 / SSD1331 / SH1106 Python library interfacing OLED matrix displays with the SSD1306, SSD1322, SSD1325, SSD1331 or SH1106 driver using I2C/SPI on the Raspberry Pi and …

Python Library – OLED display (luma.oled) Read More »

Getagd met bibliotheek, Display, Library, OLED, programmeren, Python, SH1106, SSD1306, SSD1322, SSD1325, SSD1331

Arduino Library – LiquidTWI2

by SebastiaanPosted on 2017-06-18 Geplaatst in Arduino libraries

Installatie van Arduino IDE libraries: Arduino info A lean, high speed I2C LCD Library for Arduino, which supports MCP23008 (Adafruit LCD Backpack) and MCP23017 (Adafruit RGB LCD Shield)A lean, high speed I2C LCD Library for Arduino, which supports MCP23008 (Adafruit LCD …

Arduino Library – LiquidTWI2 Read More »

Getagd met Arduino, bibliotheek, I2C, Library, LiquidTWI2

Python Library – APDS9930

by SebastiaanPosted on 2017-02-26 Geplaatst in Python libraries

Informatie (ENG): Python module for the APDS-9930 I2C Ambient Light and Proximity sensor This is a Python port of the AVR APDS-9930 library. Simple and easy to use. Makes heavy use of Python-specific programming concepts, such as properties, to make …

Python Library – APDS9930 Read More »

Getagd met APDS9930, APDS9960, bibliotheek, Library, programmeren, Python, Raspberry pi

Arduino Library – LCDKeypad

by SebastiaanPosted on 2017-02-25 Geplaatst in Arduino libraries

Installatie van Arduino IDE libraries: Arduino info Informatie (ENG): Extends the LiquidCrystal library. Download @ forum.arduino.cc

Getagd met Arduino, bibliotheek, LCDKey, Library

Arduino Library – toneAC

by SebastiaanPosted on 2017-02-20 Geplaatst in Arduino libraries

Installatie van Arduino IDE libraries: Arduino info Informatie (ENG): Replacement to the standard tone library with many advantages: Nearly twice the volume (because it uses two out of phase pins in push/pull fashion) Higher quality (less clicking) Capability of producing higher …

Arduino Library – toneAC Read More »

Getagd met Arduino, bibliotheek, clock signal, Khz, Library, toneAC

Python Library – BMP085 / BMP180 (GY-68)

by SebastiaanPosted on 2016-12-09 Geplaatst in Python libraries

Python Library – BMP 085/180 Hardware: Informatie (ENG): Python library for accessing the BMP series pressure and temperature sensors like the BMP085/BMP180 on a Raspberry Pi or Beaglebone Black. To install, download the library by clicking the download zip link to …

Python Library – BMP085 / BMP180 (GY-68) Read More »

Getagd met bibliotheek, BMP 085, BMP 180, Library, programmeren, Python, Raspberry pi

Python Library – PIGPIO

by SebastiaanPosted on 2016-09-14 Geplaatst in Python libraries

PIGPIO Website Informatie (ENG): pigpio is a C library for the Raspberry which allows control of the general purpose input outputs (gpios). Features

sampling and time-stamping of gpios 0-31 between 100,000 and 1,000,000 times per second.

provision of PWM on any number of the user gpios simultaneously.

provision of servo pulses on any number of the user gpios simultaneously.

callbacks when any of gpios 0-31 change state (callbacks receive the time of the event
accurate to a few microseconds).

notifications via pipe when any of gpios 0-31 change state.

callbacks at timed intervals.

reading/writing all of the gpios in a bank (0-31, 32-53) as a single operation.

individually setting gpio modes, reading and writing.

socket and pipe interfaces for the bulk of the functionality in addition to the
underlying C library calls.

the construction of arbitrary waveforms to give precise timing of output gpio
level changes (accurate to a few microseconds).

software serial links using any user gpio.

rudimentary permission control through the socket and pipe interfaces so users
can be prevented from "updating" inappropriate gpios.

creating and running scripts on the pigpio daemon.

sampling and time-stamping of gpios 0-31 between 100,000 and 1,000,000 times per second.

provision of PWM on any number of the user gpios simultaneously.

provision of servo pulses on any number of the user gpios simultaneously.

callbacks when any of gpios 0-31 change state (callbacks receive the time of the event

accurate to a few microseconds).

notifications via pipe when any of gpios 0-31 change state.

callbacks at timed intervals.

reading/writing all of the gpios in a bank (0-31, 32-53) as a single operation.

individually setting gpio modes, reading and writing.

socket and pipe interfaces for the bulk of the functionality in addition to the

underlying C library calls.

the construction of arbitrary waveforms to give precise timing of output gpio

level changes (accurate to a few microseconds).

software serial links using any user gpio.

rudimentary permission control through the socket and pipe interfaces so users

can be prevented from "updating" inappropriate gpios.

creating and running scripts on the pigpio daemon.

Interfaces The library provides a number of control interfaces

the C function interface

the /dev/pigpio pipe interface

the socket interface (used by the pigs utility and the Python module)

the C function interface

the /dev/pigpio pipe interface

the socket interface (used by the pigs utility and the Python module)

Utilities A number of utility programs …

Python Library – PIGPIO Read More »

Getagd met bibliotheek, Library, pigpio, programmeren, Python