Plugwise Stretch 2.0 – Boot environment
Om de boot environment van de Smile P1 weer te geven kies optie 4 in het bootmenu en type “printenv” Ps. houd de “4” ingedrukt (in PuTTY) anders werkt het niet!
|
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 |
RT3883 # printenv bootcmd=tftp bootdelay=2 baudrate=115200 ethaddr="00:AA:BB:CC:DD:10" ramargs=setenv bootargs root=/dev/ram rw addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname):$(netdev):off addmisc=setenv bootargs $(bootargs) console=ttyS0,$(baudrate) ethaddr=$(ethaddr) panic=1 flash_self=run ramargs addip addmisc;bootm $(kernel_addr) $(ramdisk_addr) kernel_addr=BFC40000 u-boot=u-boot.bin load=tftp 8A100000 $(u-boot) u_b=protect off 1:0-1;era 1:0-1;cp.b 8A100000 BC400000 $(filesize) loadfs=tftp 8A100000 root.cramfs u_fs=era bc540000 bc83ffff;cp.b 8A100000 BC540000 $(filesize) test_tftp=tftp 8A100000 root.cramfs;run test_tftp ethact=Eth0 (10/100-M) filesize=3c0004 fileaddr=80800000 ipaddr=192.168.1.222 serverip=192.168.1.73 autostart=no bootfile=omni-emb-hpm-squashfs-sysupgrade.bin stdin=serial stdout=serial stderr=serial |
Hele boot:
|
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 |
U-Boot 1.1.3 (Aug 14 2012 - 15:05:21) Board: Omnima HPM DRAM: 64 MB relocate_code Pointer at: 83fb0000 ************** Init GPIO Pin Start ************** ************** Init GPIO Pin Done ************** spi_wait_nsec: 30 spi device id: c2 20 18 c2 20 (2018c220) find flash: MX25L12805D raspi_read: from:30000 len:1000 raspi_read: from:30000 len:1000 ============================================ Ralink UBoot Version: 3.5.3.0 -------------------------------------------- ASIC 3883_MP (MAC to GigaPHY Mode) DRAM_CONF_FROM: Boot-Strapping DRAM_TYPE: DDR2 DRAM_SIZE: 512 Mbits DRAM_WIDTH: 16 bits DRAM_TOTAL_WIDTH: 16 bits TOTAL_MEMORY_SIZE: 64 MBytes Flash component: SPI Flash Date:Aug 14 2012 Time:15:05:21 ============================================ icache: sets:512, ways:4, linesz:32 ,total:65536 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 500 MHZ #### estimate memory size =64 Mbytes Please choose the operation: 0: Load ucos code to SDRAM via TFTP Client. 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. You choosed 4 raspi_read: from:40028 len:6 You choosed 4 0 raspi_read: from:40028 len:6 . 4: System Enter Boot Command Line Interface. U-Boot 1.1.3 (Aug 14 2012 - 15:05:21) RT3883 # help ? - alias for 'help' bootm - boot application image from memory cp - memory copy erase - erase SPI FLASH memory go - start application at address 'addr' help - print online help loadb - load binary file over serial line (kermit mode) md - memory display mdio - Ralink PHY register R/W command !! mm - memory modify (auto-incrementing) mw - memory write (fill) nm - memory modify (constant address) printenv- print environment variables reset - Perform RESET of the CPU rf - read/write rf register saveenv - save environment variables to persistent storage setenv - set environment variables spicmd - read/write data from/to eeprom or vtss tftpboot- boot image via network using TFTP protocol version - print monitor version RT3883 # printenv bootcmd=tftp bootdelay=2 baudrate=115200 ethaddr="00:AA:BB:CC:DD:10" ramargs=setenv bootargs root=/dev/ram rw addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname):$(netdev):off addmisc=setenv bootargs $(bootargs) console=ttyS0,$(baudrate) ethaddr=$(ethaddr) panic=1 flash_self=run ramargs addip addmisc;bootm $(kernel_addr) $(ramdisk_addr) kernel_addr=BFC40000 u-boot=u-boot.bin load=tftp 8A100000 $(u-boot) u_b=protect off 1:0-1;era 1:0-1;cp.b 8A100000 BC400000 $(filesize) loadfs=tftp 8A100000 root.cramfs u_fs=era bc540000 bc83ffff;cp.b 8A100000 BC540000 $(filesize) test_tftp=tftp 8A100000 root.cramfs;run test_tftp ethact=Eth0 (10/100-M) filesize=3c0004 fileaddr=80800000 ipaddr=192.168.1.222 serverip=192.168.1.73 autostart=no bootfile=omni-emb-hpm-squashfs-sysupgrade.bin stdin=serial stdout=serial stderr=serial |